How to install Fontana Edinburgh Wall Mount Thermostatic Rainfall Shower Set With 6 Body Massage Jets | CHROME-SQUARE-RAIN-SHOWER-HEAD
Installation Instructions for Bathroom Shower Set
Before you begin, please read the installation instructions below. Observe all local building and safety codes.
Unpack and inspect the product for any shipping damages. If you find damages, do not install.
Please note all products must be installed by a professional and certified plumber otherwise warranty might be voided.
shower
Wall Mount Shower Head Installation Instructions
Step 1:
shower
Step 2:
Step 3:
Step 4:
Step 5:
Step 6:
Step 7:
1. Apply plumber's tape to the threads on both ends of the shower arm and slide on the decorative escutcheon.
2. Insert the new arm into the fitting in the wall and twist to tighten. Finish tightening with your adjustable wrench. Wrap a dry cloth around the shower arm to protect the finish while tightening with an adjustable wrench.
3. Thread the new showerhead onto the arm and hand-tighten. Hold the shower arm in place with groove joint pliers and finish tightening the shower head with your adjustable wrench. Wrap both in a dry cloth to protect the finish.
4. Before securing the decorative escutcheon, turn on the water supply to make sure that all connections are tight and there is no leaking. If no leaks are detected, continue with the installation. If leakage does occur, use your adjustable wrench to tighten the connections as necessary.
5. Apply a bead if silicone sealant to the back of the escutcheon and press firmly into place against the installation surface. Wipe away any excess sealant with your damp cloth.
Hand Held Shower Installation Instructions
Size
rts Included:
1. Wall Outlet 2. 60" Shower Hose With Gaskets 3. Complete Slide Bar With Mounting Parts / Posts, Screws & Anchors 4. Adjustable Shower Mount (Attached To Slide Bar) 5. Hand Held Shower
HandHeld Shower Installation Instructions
Handshower Installation Instructions
Supply Elbow Installation
Wall Bar Installation
Step 1:
Step 2:
Apply Plumber Tape To Threaded Ends Of 1/2" (13 Mm) Iron Pipe Nipple (Not Supplied) And Thread Into Shower Riser Elbow So That Nipple Extends Past The Finished Wall No More Than 0.2" (4.8 Mm) And No Less Than 1/16" (1.6 Mm). Place The Supplied Installation Gasket (1) Behind The Elbow (2). Screw The Supply Elbow Onto The Nipple Making Sure That The Supply Elbow Outlet Is In A Downward Facing Position. Minimum Diameter For Hole Is 1" (25 Mm) With A Maximum Of 1½” (38 Mm).
Caution: To Avoid Damage To The Supply Elbow Or Hose Finish During Installation, Wrap With A Cloth Or Tape And Use Only A Smooth-Jawed Wrench. DO NOT OVERTIGHTEN CONNECTIONS.
A. Select A Convenient Height To Place The Shower Rail Based On Your Personal Needs. Be Sure To Leave Enough Slack For The Hose Of The Hand Shower To Operate Freely When The Hand Shower Is Placed In The Extreme Up Or Down Positions. Note: If Possible It Is Recommended That The Slide Bar Brackets Be Secured Into The Wall Studs. For Ceramic Tile Installation, Drill Holes In Grout If Possible.
B. Mark The Place For Drilling The Hole For The Lower Post. Mark Using A Level, In A Vertical Line From The Lower Hole, The Placement Of The Upper Post Hole. Distance Approximately 25.7" (653 Mm).
Step 3:
Step 4:
Note: Hole Size Will Be Determined By Your Use Of Just The Screw Or Anchor And Screw For Installation. Drill Hole For Mounting Of Bottom Post. Start With A Smaller Drill Bit Size, 1/8" Is Recommended, And Drill Hole. If You Hit A Wall Stud, Go To Next Step. If You Do Not Hit A Wall Stud, Change To A Drill Bit Size Suitable For The Anchors, 1/4" Is Recommended, And Re-Drill Hole. Anchors Are For Use On Drywall Or Tile. For Fiberglass, Acrylic And Flat Plastic Surfaces, Use Toggle Bolts (Not Included). Before Drilling Top Mounting Hole, It Is Recommended That You Place The Assembled Slide Bar And Post Assembly (1) On Its Side Next To The Hole Locations You Have Marked. Make Sure Posts Are Pressed Fully Onto Bar. Align Centre Of Bottom Post With Bottom Hole That Was Just Drilled And Make Sure Centre Of Top Post Aligns With Mark For Top Hole. If Not, Re-Mark Top Hole Location. If It Aligns, Drill Top Hole In Location As Marked.
Insert Anchors (1) Into Drilled Holes. Slide Covers (2) Over Brackets (3), And Insert Screws (4) Into Bracket/Cover Assembly. Secure Assembly To Wall With Screws.
Slide The Slide Mechanism (1) And Elbow (2) Onto The Wall Bar (3). Slide Wall Bar Over Bracket Tabs (4) And Secure The Wall Bar Unit With Screws (5) Provided. Install Caps (6) Into Ends Of Wallbar. Lower Elbow (7) & Screw (8) Was Pre-Installed Prior To Shipping, Tighten Screw (9) If You Find It Is Sliding Inside Bar.
Step 5:
Step 6:
Connect The Shower Hose To The Wall Outlet (1) And The Hand Held Piece (2), Ensuring That The Internal Gaskets (3) Are Present In The Shower Hose Nuts. Normal 1/2" Rubber Gaskets Can Be Used.
Place The Conical Nut Of The Hose (4) That Is Connected To The Hand Held Piece, In The Slide Bar Holder (5) And Turn It To Desired Position.
To Slide The Mechanism Up Or Down, Push In On The Button (6) Of The Mechanism And Slide It On The Bar.
Step 7:
Care Should Be Given To The Cleaning Of This Product. Although Its Finish Is Extremely Durable, It Can Be Damaged By Harsh Abrasives Or Polish. To Clean, Simply Wipe Gently With A Damp Cloth And Blot Dry With A Soft Towel.
Maximum Flow Rate: 2.5 GPM
Shower Body Jets Installation Instructions
Step 1:
Step 2:
Body Sprays installation
Step 3:
Step 4:
Step 5: (Pressure Balancing Loop)
Rough-in Suggestion: This installation requires a 1/2" male threaded pipe fitting to extend 1/4" beyond the finished surface. The plumber should install a properly anchored 1/2" female pipe fitting (i.e. a drop-ear ell) recessed into the wall, into which a brass pipe nipple of proper length can be fitted once the finished wall is complete. Note: The hole size opening should be 1.5" max diameter. Bodyspray placement: Custom shower systems are sized to the user or users. Bodysprays are normally placed at the upper back, middle back, and upper thigh. Always position bodysprays according to the preferences of the user(s).
Pressure Balancing Loop: If installing bodysprays in a bank of 3 or fewer, a pressure balancing loop is not necessary. If installing bodysprays in a bank of 4 or greater, a pressure balancing loop must be used to keep the pressure even between the bodysprays.
Instructions Body jets should be arranged in your system to provide the necessary spray outlets to suit the application. 1. Identify all components and check for completeness, particularly before arranging fitting. 2. Depending on the application the body jet can be panel mounted using a backnut (not supplied) or set into the wall on rigid pipe work. If panel mounting care should be taken to ensure connection can be made after securing with the backnut. 3. Connect body jet to pipe work using recommended ½” BSP connections (not provided) with thread sealing compound where necessary. Note: - Before finishing wall turn on water supplies to check both correct system function and for leaking from joints/connections. 4. Complete wall finish.
Fontana Edinburgh Wall Mount Thermostatic Rainfall Shower Set With 6 Body Massage Jets
This beautifully designed square rainfall shower system will provide your bathroom with a touch of elegance and your muscles with the relief they need. This rainfall showerhead will provide relaxation while the six adjustable body massage jets will target the areas that need it most. Handheld shower and thermostatic faucet system included. Three lever control bathroom shower in brushed nickel or chrome finish is the perfect complement to today's modern home. This FontanaShower is ceiling mount complete shower head, handheld shower mixer set provides a luxurious showering experience and is the perfect complement to any modern bathroom. The modern design handheld shower, cold and hot water shower mixer and an easy-to-use mixer valve, made from high-quality. Be sure, when it comes to new bathroom rain shower sets, FontanaShowers is offering shape, finish, and styles you're looking for.
Features:
Brand Name: FontanaShowers
Model Number: CHROME-SQUARE-RAIN-SHOWER-HEAD
Water Outlets: Handheld Shower, Shower Head, Body-Jet Spray
