Fontana Lima Ultra Waterfall System Light Oil Rubbed Bronze
This system is an explosion of water! Generously sized at 22" inches in length, this wall mount rainfall showerhead also provides a cascade of water to increase your relaxation. There are six adjustable jets, and each provides 16 massaging streams of water for your weary neck, shoulder and back muscles. Additionally, there is a handheld shower to ensure all-over coverage. The oil rubbed bronze color is warm and inviting. All shower parts are made of solid brass making this shower durable and sturdy yet light to the hands. Now you can step out of the shower feeling clean and rejuvenated, thanks to this awesome body massage waterfall shower set.
Fontana Lima Ultra Waterfall System Light Oil Rubbed Bronze Features:
Brand Name: FontanaShowers
Model Number: FS-762-ORB
Material: Solid Brass
Shower Head Size: 22"
Water Flow Rate: 18 (L/Min) 4.8 GPM
Shower Hose: Double locked 59" (1.5m)
Valve: Pressure balance water pressure control
Connection: Standard plumbing connection
Pressure: Minimum 29 psi / maximum of 72.7 psi
Ceramic Disc Technology: ½" NPT Inlets and Outlets
1. Open the top cover and drill according to the marked position.
Mark by the position of the four holes.
Take care to avoid wires and pipes to prevent damage.
Be sure to confirm that the four holes are on the same horizontal line.
2. Two inlet fittings are connected to the pipe joint of the wall; then the nut, expansion screw, and inlet pipe are connected.
3. Reinstall the top cover.
Hand-Held Shower Instructions
5. HOLE LOCATIONS FOR WALL MOUNT
Remove Front Cover (5A) from Wall Mount (5B). Use Wall Mount Screw Holes (5C) to place the desired location. Using a punch or awl, tap the screw hole locations. Holes must be vertically aligned.
ANCHOR INSTALLATION
Drill two 1/4” dia. Holes (6A). If installing into a studs drill two 1/8” dia. holes and do not use Anchors (6B). Insert Anchors (6B) into Holes (6A) and tap flush with wall.
WALL MOUNT INSTALLATION
Place Wall Mount (7A) into wall and inset Mounting Screws (7B) through Wall Mount Holes (7C) and tighten until Wall Mount (7A) is flush with the wall. Do Not Over Tighten! Insert Front Cover (7D) into Wall Mount (7A)
DROP ELBOW & HOSE INSTALLATION
Apply PTFE plumbers tape on both ends of Pipe Nipple (8A) (not included). Screw Pipe Nipple (8A) into the elbow inside the wall. The Pipe Nipple (8A) is to project 1/4” – 3/4” from the finished wall. Screw Drop Elbow (8B) onto Pipe Nipple (8A) and tighten until Drop Elbow (8B) is property positioned and flush to the finished wall.
Place Rubber Seal (8C) inside Hex Hose Fitting (8D). Connect Hex Hose Fitting (8D) into Drop Elbow Outlet (8E) by turning Hex Hose Fitting (8D).
UNIT STARTUP
Turn on hot and cold water supplies, and check all connections for leaks.
FINAL FLUSHING
For final flushing, turn the valve on and allow water to run through the Hose (10A) for several minutes. Allow water to run for several minutes until all foreign matter clears the line.
11. SHOWER ARM INSTALLATION Place Rubber Seal (11A) inside Tapered Hose Fitting (11B). Conned Hand Shower (11C) to Hose (11D) by turning Tapered Hose Fitting (118) clockwise.
Mixer Installation
a.Release four handwheel levers according to above directions.
b.Take apart the embed valve, panel, and handwheel.
1. Dig the embed space for the pipe on the wall according to the specification of the valve.
2. Dig 4 holes according to the position of the screws.
3. Use a hammer to thwack the screws into 4 holes.
4. Fix the valve body with 4 screws.
5. Find out the expansion screw heads with washer and spring washer. Use copper sleeve wrench to lock the screw heads with the embed valve body.
6. After connect all the pipes and before sealing the wall with concrete, confirm no leaking problem occur when turn on the water.
7. Fix the decorative panel on the embed valve body.
8. Screw the handwheel arms with the handwheels.
Body-Jet Installation
Install the Supply Piping
Multiple Bodyspray Installation
•Water Supply
•Nipple Mamelon Nipple
•Pressure Balancing Loop
1. Route the water supply lines.
2. If installing more than one bodyspray off the same supply line, construct a pressure balancing loop. Locate a tee along the loop at each bodyspray installation location.
3. Do not strap the pipes at this time.
Single Bodyspray Installation
•Nipple Mamelon Nipple
1. Route the water supply line.
2. Install an elbow to the end of the supply pipe at the bodyspray installation location.
Install the Plaster Guard
Install the Plaster Guard
•Elbow (or Tee)
•Install the plaster guard
Set Piping Depth
Align mark with front of the stud face
•Thin Wall
Align mark with front of the stud face
•Standard Wall
Install the plaster guard. Push until the plaster guard is snug against the face of the elbow (or tee).
1. Install the water-resistant wall board.
2. Cut out a 4" (10.2 cm) to 4-1/4" (10.8 cm) square at each the installation location.
3. Install the finished wall material
•Escutcheon
•Leak Shield
•Adapter
•Extension
•Socket Wrench With Bit
•Screw
•Waterway Passage
1. Insert the escutcheon into the rough opening. The double ribs of the leak shield should be facing up.
2. If the leak shield makes contact with the elbow: Enlarge the hole in the back of the leak shield to 1-1/4" (3.2 cm).
3. Thread the adapter onto the nipple using the provided 11 mm bit, 11 mm or 7/16" socket, extension and socket wrench. Use masking tape to hold the bit in place, as the bit could fall off and cause damage.
IMPORTANT! The escutcheon should sit loosely at this point. If it is tight against the wall, use a longer pipe nipple.
4. Align the groove in the waterway with the double ribs on the leak shield.
5. Press the waterway into place over the adapter. Secure the waterway to the adapter with the screw provided.
6. Verify that the escutcheon does not turn or shift.
With the ribs of the sprayhead facing up, install the sprayhead to the waterway.