Fontana Océane Wall Mount Multi-Functional Shower System
This hi-tech, stylish and multi-functional shower system offers great performance and maximum comfort. Wall mount showerhead features waterfall, rainfall or a combination of both. The handheld shower conveniently provides extra all over coverage. The six massage jets offer stress relief after a hard day, while the LED light will help achieve the perfect relaxation moment. Modern chrome finish on materials made of steel and brass to ensure durability.
Fontana Océane Wall Mount Multi-Functional Shower System Features:
Brand Name: FontanaShowers
Model Number: FS845RBP
Type: Shower Set
Cold/Hot Water Control Type: Dual Holder Dual Control
Style: Contemporary
Number of Handles: Five Handles
Surface Treatment: Polished
Type: Fixed Support Type
Valve Core Material: Ceramic
Surface Finish: Stainless Steel
Installation Type: Wall Mount
Surface Finish: Chrome
Size: (27.56"x14.96") 700x380 MM
Valve: Hot And Cold Valve
Material: 304 SUS ,Brass
LED Light: Single Color
Function: Rainfall, Waterfall, Misty, Water Column
Before you begin, please read the installation instructions below. Observe all local building and safety codes.
Unpack and inspect the product for any shipping damages. If you find damages, do not install.
Please note all showers must be installed by a professional and certified plumber otherwise warranty might be voided.
Installation Instructions
Shower Head Installation Instructions
Step 1:
Step 2:
shower
Open the top cover and drill according to the marked position. 1. Mark by the position of the four holes. 2. Take care to avoid wires and pipes to prevent damage. 3. Be sure to confirm that the four holes are on the same horizontal line.
Remove the protective cover (F). Mark the positions and drill holes to suit the anchors (A). Install the anchors (A) and fix the rough-in valve (B) into the wall with screws. Use a level to ensure that the rough-in valve (B) is straight and level. (Important: Flush the water supply to remove any dirt and debris before installing the valve body).
Shower Head Installation Instructions
Step 3:
Step 4:
Wrap Teflon tape around the pipe threads and connect water supply lines and in-wall pipes (not included) as desired to the rough-in valve (B). Turn on the water supply and open the cartridge to check for leakage. Then put on the protective cover and finish the wall surrounding the valve. (Note: Test the water pressure after the pipe connections have been made and before the finished wall material is installed).
Two inlet fittings are connected to the pipe joint of the wall; then the nut, expansion screw, and inlet pipe are connected.
Shower Head Installation Instructions
Step 5:
Step 6:
Reinstall the top cover.
Fix the escutcheon (D) to the showerhead (E) with screws (C).
Shower Head Installation Instructions
Step 7:
Remove the protective cover when the finished wall is completed. Then, install the showerhead (E) and press it against the finished wall.
Shower Head Installation Instructions
Shower Head Installation Instructions
Hand-Held Shower Installation Instructions
Step 1:
Step 2:
Step 3 & 4:
Hand
Held
Shower
Hand Held Shower
Handheld Shower
Handheld Shower
Handheld Shower
Step 5:
Step 6 & 7:
Step 8:
1. Gather All Parts
2. Hole Locations For Wall Mount
Remove Front Cover (A) from Wall Mount (B). Use Wall Mount Screw Holes (C) to place the desired location. Using a punch or awl, tap the screw hole locations. Holes must be vertically aligned.
3. Anchor Installation
Drill two 1/4” dia. Holes (A). If installing into a studs drill two 1/8” dia. holes and do not use Anchors (B). Insert Anchors (B) into Holes (A) and tap flush with the wall.
4. Wall Mount Installation
Place Wall Mount (A) into wall and inset Mounting Screws (B) through Wall Mount Holes (C) and tighten until Wall Mount (A) is flush with the wall. Do Not Over Tighten! Insert Front Cover (D) into Wall Mount (A)
5. Drop Elbow & Hose Installation
Apply PTFE plumbers tape on both ends of Pipe Nipple (A) (not included). Screw Pipe Nipple (A) into the elbow inside the wall. The Pipe Nipple (A) is to project 1/4” – 3/4” from the finished wall. Screw Drop Elbow (B) onto Pipe Nipple (A) and tighten until Drop Elbow (B) is property positioned and flush to the finished wall. Place Rubber Seal (C) inside Hex Hose Fitting (D). Connect Hex Hose Fitting (D) into Drop Elbow Outlet (E) by turning Hex Hose Fitting (D).
6. Unit Startup
Turn on hot and cold water supplies, and check all connections for leaks.
7. Final Flushing
For final flushing, turn the valve on and allow water to run through the Hose (A) for several minutes. Allow water to run for several minutes until all foreign matter clears the line.
8. Shower Arm Installation
Place Rubber Seal (A) inside Tapered Hose Fitting (B). Conned Hand Shower (C) to Hose (D) by turning Tapered Hose Fitting (B ) clockwise. Warning: Make sure Hand Shower (C) is securely tightened to Hose (D).
HandHeld Shower Installation Instructions
Body Jets Installation Instructions
Step 1:
Step 2:
Body sprays
Remove the decorative plate (A) out of the body.
Remove the screws from the outlet face (B) and connector body (C) with the Allen key (D).
Body Spray Installation Instructions
Step 3:
Step 4:
Screw the threaded pipe (E) to the water supply fittings. Push the plastic box (F) into the wall through the threaded pipe (E). Then, install the decorative plate (I) into the plastic box (F). Make sure the position is correct according to the diagram.
Screw the connector (G) into the threaded pipe (E) with the Allen key (H). Install the connector body (C) to the connector (G). When finish installation, please check to make sure the connection is completed. Then, fix the screws into the body (C) with Allen key (D) and make sure the body (C), connector (G) and decorative plate (I) are tightened. Make sure the one side with the bulge is in the top position.
Body Spray Installation Instructions
Step 5:
Step 6:
Install the outlet face (B) to the body (C). Make sure the connection of body (C) and outlet face (B) are completed. Tighten the screw through the outlet face (B) into the body (C) with the Allen key (D).
Install the decorative plate (A) into the outlet face (B) tightly. Make sure the hole and the raised dot are in the correct position when you push the decorative plate (A) into the outlet face (B).
Body Spray Installation Instructions
Body Spray Installation Instructions
Thermostatic Mixer Installation Instructions
Step 1:
Step 2:
Mixer
Valve
Release 4 handwheel levers according to the above directions. Take apart the embed valve, panel, and handwheel.
Mixer Control Valve Installation Instructions
Step 3:
Step 4:
Dig the embed space for the pipe on the wall according to the specification of the valve. Dig 4 holes according to the position of the screws.
Use a hammer to thwack the screws into 4 holes. Fix the valve body with 4 screws.
Mixer Control Valve Installation Instruction
Step 5:
Step 6:
Find out the expansion screw heads with washer and spring washer. Use copper sleeve wrench to lock the screw heads with the embed valve body.
After connecting all the pipes and before sealing the wall with concrete, confirm no leaking problem occurs when you turn on the water.
Mixer Control Valve Installation Instruction
Step 7:
Step 8:
Fix the decorative panel on the embed valve body.
Screw the handwheel arms with the handwheels.
Mixer Control Valve Installation Instruction
Step 9:
Step 10:
Mixer Control Valve Installation Instruction
Step 11:
Step 12:
Mixer Control Valve Installation Instruction
Step 13:
How to install the Shower Set with Wall Mount Showerhead, Body Jets, Hand Held Shower and Shower Mixer