Home > Installation Instruction For Fontana Trialo Color Changing LED Shower Head with Adjustable Body Jets

Fontana Sierra Light Oil Rubbed Bronze LED Shower System

Step into your new beautiful light Oil Rubbed Bronze shower with Built-in hydro-powered device powers the LED lights, which provide visual shower temperature to reduce water waste. The shower head will automatically change color according to water temperature. Lights are based on water pressure and will activate when you turn on the water. This shower system comes equipped with Six adjustable body massage jets and a handheld shower ensure complete relaxation. This Fontana Sierra Light Oil Rubbed Bronze LED Shower System rainfall shower set mixer with body jets set provides a luxurious showering experience it is the perfect complement to any modern bathroom. The modern design handheld shower, and an easy-to-use mixer valve, both made from high-quality solid brass. Easy for the elderly and children to shower, handheld showerhead, shower mixer valve control, pressure-balanced valves can prevent scalding injuries, in particular to the elderly and children. When it comes to new bathrooms, Fontana Showers offers the shape, finish and styles you're looking for.

Fontana Sierra Light Oil Rubbed Bronze LED Shower System Features:

  • Brand Name: Fontana Showers
  • Model Number: LED-SHOWER-FB-0522ORB
  • Finish: Light Oil Rubbed Bronze
  • Style: Contemporary Rain Shower head
  • Shower head Height (thickness): 0.33"
  • Shower head Width: Available in 8", 10", 12", 16", or 20"
  • Shower head Length: Available in 8", 10", 12", 16" or 20"
  • LED Power Source: Water Flow
  • LED Color: Blue, Green, Red
  • Mount Method: Wall or Ceiling Mount
  • Connection:1/2" US standard
  • Body Jets: Qty 6 - 2"x2" Solid brass 360° adjustable
  • Material: Solid Brass
  • Water temperature is ≤89 °F (≤32 °C): Blue color will show
  • Water temperature is between 97 to 107 °F (36-42 °C): Green color will show
  • Water temperature is between 109 to 122 °F (43-50 °C): Red color will show
  • Water temperature is above 122 °F (>50 °C): Red color will flash

  • Fontana Sierra Light Oil Rubbed Bronze LED Shower System
    FontanaShowers®Product Warranty InformationFontanaShowers Product Warranty
    • efore you begin, please read the installation instructions below. Observe all local building and safety codes.
    • Unpack and inspect the product for any shipping damages. If you find damages, do not install.
    • Please note all showers must be installed by a professional and certified plumber otherwise warranty might be voided.
    ------- -----

    Shower Head Installation Instructions

    Step 1: shower Step 2:

    Step 3: Step 4:

    Step 5:

    1. Apply plumber's tape to the threads on both ends of the shower arm and slide on the decorative escutcheon.

    2. Insert the new arm into the fitting in the ceiling and twist to tighten. Finish tightening with your adjustable wrench. Wrap a dry cloth around the shower arm to protect the finish while tightening with adjustable wrench.

    3. Thread the new shower head onto the arm and hand-tighten. Hold the shower arm in place with groove joint pliers and finish tightening the shower head with your adjustable wrench. Wrap both in a dry cloth to protect the finish.

    4. Before securing the decorative escutcheon, turn on the water supply to make sure that all connections are tight and there is no leaking. If no leaks are detected, continue with the installation. If leakage does occur, use your adjustable wrench to tighten the connections as necessary.

    5. Apply a bead if silicone sealant to the back of the escutcheon and press firmly into place against the installation surface. Wipe away any excess sealant with your damp cloth.

    Hand Held Shower Installation Instructions

    Step 1: hand shower Step 2:


    Step 3:

    Hand Shower Outlet Installation
    Complete the outlet pipework ensuring it ends in an appropriate 15mm x 1/2" BSP female thread elbow.

    This fitting is not supplied as variations in installations require the selection of a suitable solder or compression fitting.
    • Install the 'Wall Outlet', thread long male 1/2" BSP into the appropriate female fitting using PTFE tape to give a watertight joint.

    Note: The thread can be cut to size if required. Make sure that all debris is removed from the connector and the section that has been cut is dressed correctly, before installation.

    Shower Wall Holder Installation
    Decide the position for the shower head holder on the wall within the bath showering area and proceed as follows:
    • Hold the hand shower head holder fixing plate in a suitable position on the wall, mark out the position of the holder. Mark the two locating holes, these are 17mm center.
    • Drill and plug the wall. Use an appropriate masonary drill, but if the wall is plasterboard or a soft building block, use special wall plugs and an appropriate drill bit.
    • Slide the inserts onto the screws in the orientation. Secure the inserts by tightening the screws.
    • Slide the hand shower head holder body onto the inserts and secure by tightening the grub screw facing down.

    Shower Body Jets Installation Instructions

    Step 1: Body
    Step 2:

    Set the decorative cover on the body jet.
    Roll the raw material belt in the thread screws.

    Step 3:

    Use a wrench to tighten 6 body jets on the water outlet holes.
    Tighten it in a clockwise direction.

    Shower Valve Mixer Installation Instructions

    1. Rough-In Body x1
    2. Anchor x4
    3. Positioning Bar x2
    4. Tapping Screw 1 x4
    5. Tapping Screw 2 x4
    6. Plate x1
    7. Cover x3
    8. Button x3
    9. Screw 1 x3
    10.Diverter Handle x1
    11. Temperature Handle x1
    12. Volume Handle x1

    Step 1: Step 2:

    Step 3: Step 4:
    Attach the positioning bar to the rough-in body (4,5) with tapping screws. Mark the location of the mounting holes.
    Remove the rough-in body and drill pilot holes at the locations marked in the previous step. Insert anchors.

    Step 5: Step 6:
    Attach the rough-in body to the wall.
    Connect the rough-in body to the water supply pipes according to the diagram.

    Step 7: Step 8:
    Finish the wall surrounding the shower with a thickness of 1/2"-1-1/2".
    a) Finished wall surface should not exceed the upper edge of the installation box.
    If the tile exceeds the edges of the installation box, trim the tile as necessary to install the trim plate.
    b) Trim the tile around the installation box as necessary.
    Step 9:
    Remove the plastic guard and place the trim plate over the installation box. Install the screws covers, handles and buttons.

    How to install Shower Set with Showerhead, Hand Held Shower, Shower Mixer and Body Jets

    BathSelect Ancient Round Antique Rainfall Wall ShoweBathSelect Ancient Round Antique Rainfall Wall Shower Head Installation Instructions Head Installation Instructions