Home > Installation Instructions For Fontana Sofia Large Ceiling Rain Shower Head Set With Shower Body Sprays And Hand Shower

Fontana Sofia Large Ceiling Rain Shower Head Set With Shower Body Sprays and Hand Shower

Because one size does not fit all, there are five shower head sizes to choose from. Once you've chosen your shower head, which size body massage sprayers do you want? And lastly, round or square shape for your massage sprayers? The ultimate shower set -- that your custom-designed yourself! The Fontana Sofia Shower Set is manufactured using superior quality solid brass material. The shower system comes with a ceiling mount shower head, 6 body massage sprays with 36 rubber nozzles that give strong massage pressure, and a handheld shower to offer you complete showering convenience and a ceiling mount shower arm in 22.04" (56cm) size. When it comes to new bathroom shower sets, FontanaShowers is offering shape, finish, and styles you're looking for.

Fontana Sofia Large Ceiling Rain Shower Head Set With Shower Body Sprays and Hand Shower Features:

Brand Name: FontanaShowers
Model Number: FS-7209C
Material: Solid Brass
Shower Arm Size: 22.04" (56cm)
Shower Head Size: 20" X 20", 24" X 24", 31" X 31", 40" X 20", 40" X 40"
Body Spray Shape: Round / Square
Finish: Chrome
Water Hose Size: 59"(1.5m)
Male Thread: G1/2" x G1/2"
Water Hose Material: Stainless Steel
Working Pressure: 0.05-1.0Mpa

FontanaShowers® Product Warranty Information

Before you begin, please read the installation instructions below. Observe all local building and safety codes.
Unpack and inspect the product for any shipping damages. If you find damages, do not install.
Please note all showers must be installed by a professional and certified plumber otherwise warranty might be voided.

shower

Shower Head Installation Instructions



	shower

Step 1:		Step 2:

According to the template (B) mark the location of the mounting holes (1). Use a drill with a 6mm bit to drill mounting holes into studs or blocking.		Install the mounting brackets (C) with the tapping screws (D1). Thread the shower bars (E) onto the mounting brackets, and the inlet hose (F) onto the water inlet.

Step 3:		Step 4:

Attach the shower head (A) to the shower bars (E). Connect the inlet hose (F) to the showerhead.

Step 5:

Hand Held Shower Installation Instructions

Step 1:	hand shower	Step 2:
			HAND HELD SHOWER

Step 3:

Hand Shower Outlet Installation • Complete the outlet pipework ensuring it ends in an appropriate 15mm x 1/2" BSP female thread elbow. Note: This fitting is not supplied as variations in installations require the selection of a suitable solder or compression fitting. • Install the 'Wall Outlet', thread long male 1/2" BSP into the appropriate female fitting using PTFE tape to give a watertight joint. Note: The thread can be cut to size if required. Make sure that all debris is removed from the connector and the section that has been cut is dressed correctly, before installation. Shower Wall Holder Installation Decide the position for the shower head holder on the wall within the bath showering area and proceed as follows: • Hold the hand shower head holder fixing plate in a suitable position on the wall, mark out the position of the holder. Mark the two locating holes, these are 17mm center. • Drill and plug the wall. Use an appropriate masonary drill, but if the wall is plasterboard or a soft building block, use special wall plugs and an appropriate drill bit. • Slide the inserts onto the screws in the orientation. Secure the inserts by tightening the screws. • Slide the hand shower head holder body onto the inserts and secure by tightening the grub screw facing down.

Shower Body Sprays Installation Instructions

Step 1:	body jet	Step 2:

A. Connector B. Connector Screws (x2) C. Bracket Screws (x4) D. Bracket E. Plaster Guard F. Test Plug G. Test Plug Nut H. 1/8" Hex Wrench		I. Housing J. Housing Nut K. Spray Assembly L. Grease Packet M. Trim Ring-Square N. Trim Ring-Round O. Set Screw P. 9/64" Hex Wrench Q. 1/16" Hex Wrench R. Filter
Step 3: (Rough-In)		Step 4:


Step 5:		Step 6:


Step 7:		Step 8:

Plumb the connector to water supply lines.
Step 9:		Step 10:


Step 11:


Step 12: (Installation)		Step 13:


Step 14:		Step 15:

		If distance is less than or equal to 2-1/8" (54mm), proceed to step 13. If distance is greater than 2-118", order 1" extension kit.
Step 16:		Step 17:

		Tighten housing nut (J) until housing (I) is secure and does not spin on wall.
Step 18:		Step 19:

Flush system before the next step.
Step 20:		Step 21:


Step 22:

To Re-install: Reverse steps A through C, then turn on water supply.

Shower Mixer Installation Instructions

Parts: 1. Rough-In Body x1 2. Anchor x4 3. Positioning Bar x2 4. Tapping Screw 1 x4 5. Tapping Screw 2 x4 6. Plate x1 7. Cover x3 8. Button x3 9. Screw 1 x3 10.Diverter Handle x1 11. Temperature Handle x1 12. Volume Handle x1	Shower Mixer

Step 1:		Step 2:
	Shower Mixer


Step 3:		Step 4:

Attach the positioning bar to the rough-in body (4,5) with tapping screws. Mark the location of the mounting holes.		Remove the rough-in body and drill pilot holes at the locations marked in the previous step. Insert anchors.

Step 5:		Step 6:

Attach the rough-in body to the wall.		Connect the rough-in body to the water supply pipes according to the diagram.

Step 7:		Step 8:

Finish the wall surrounding the shower with a thickness of 1/2"-1-1/2". a) Finished wall surface should not exceed the upper edge of the installation box.		If the tile exceeds the edges of the installation box, trim the tile as necessary to install the trim plate. b) Trim the tile around the installation box as necessary.

Step 9:

Remove the plastic guard and place the trim plate over the installation box. Install the screws covers, handles and buttons.
Shower Valve Mixer Installation