Home > Installation Instructions for Holguin Bathtub Faucet

Holguin Dual Handle Deck Mount Bathtub Faucet

With a modern design, the Holgui bathtub faucet is original and eye-catching. The twist handles and the bright chrome finish make it ideal for contemporary bathrooms. It can be used either for the bathtub or the bathroom sink. It is deck mount and it requires three hole installation, with separate handles for hot and cold water. Only the best materials have been used – the faucet is made of brass, for a long lasting life time. It comes with complete accessories and installation instructions.

Holguin Dual Handle Deck Mount Bathtub Faucet Features:

  • Brand Name: FontanaShowers
  • Model Number: FS149TTC
  • Type: Bathtub Faucet
  • Faucet Height: 8 5/8"
  • Spout Height: 7 5/8"
  • Spout Reach: 5 11/16"
  • Flow Rate: 2.4 GPM at 20 PSI
  • Certification: UPC, cUPC, NSF certified compliant
  • Design: Twist
  • Faucet Body Material: Brass
  • Faucet Finish: Chrome
  • Holguin Dual Handle Deck Mount Bathtub Faucet

    FontanaShowers® Product Warranty Information FontanaShowers Product Warranty



    • Before you begin, read the installation instructions below. Observe all local building and safety codes.
    • Unpack and inspect the product for any shipping damages. If you find damages, do not install it.If you need assistance or have questions while installing your shower set, contact Customer Service.
    • We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures, and plumbing.

    TOOLS AND MATERIALS:

    • Screwdriver
    • Teflon Tape

    INSTALLATION
    1. If your faucet comes with the brass T attached to the faucet body, unthread and remove the T and associated
    hardware.
    2. Thread the silver mounting washer and rubber sealing gasket on the faucet body.
    3. Apply a bead of silicone sealant to the underside of the spout, or faucet base, and thread through the center
    mounting hole.
    4. Thread the mounting hardware and brass T onto the spout pipe and hand-tighten to secure.
    5. Check to make sure the faucet is properly aligned and adjust as needed. When the faucet is in the proper position,
    finish tightening mounting hardware with your adjustable wrench.
    Tip: Make sure that the T outlets are aligned at an angle to allow maximum clearance for water connections.
    6. Wipe away any excess sealant around the faucet base using your damp cloth.
    7. Assemble the handles by screwing the lock nuts down to the end of the handle bodies. If handles are assembled
    move on to step 8.
    8. Insert the handle bodies up through the mounting holes. Thread the plastic slip washers and rubber sealing gaskets
    onto the handle bodies to secure.
    9. Hand tighten to attach the hot and cold flexible water feed tubes to the handle bodies and brass T. Give a ¼ turn with
    pliers or wrench, but don’t overtighten. (Hot water is always on the left and cold water is always on the right.) Curve
    tubes as necessary to ensure there are no kinks or knots.
    10. Place the handle assemblies on the handle bodies. Make sure that both handles are in the OFF position and tighten
    the set screw on the top or side of the handle with Allen wrench (provided).
    11. Connect the main water supply to the faucet body.
    12. To install the new pop-up drain, apply a bead of silicone sealant to the underside of the drain flange and place it in the mounting hole. If there is no pop-up drain, move on to step 16.
    13. Thread the lock nut onto the drain pipe and tighten with your adjustable wrench.
    14. Wipe away any excess sealant around the drain using your damp cloth.
    15. Push the pop-up rod down through the faucet body. Attach the pop-up rod to the pivot rod with the extension rod.
    Adjust the rods so that the drain stopper opens and closes properly.
    16. Attach the P trap to the drain pipe and wall drain fitting and tighten the locknuts.
    17. When your faucet installation is complete, turn on the water supply. Check to make sure that all connections are tight
    (no water should be leaking) and that the hot and cold supplies are working correctly. Turn the water on and allow
    the water to flow through the spout for approximately 60 seconds.



    Bravat Chrome Finish Dual Handle Bathroom Sink Faucet
    Bravat Chrome Finish Dual Handle Bathroom Sink Faucet


    Shower Installation Instructions