How to install Electrical Sensor Commercial Sink Basin Brushed Nickel Faucet | FS5061-B
Easy step by steps Installation Instructions for Sensor Faucet
Visit Product Page
Before you begin, please read the installation instructions below. Observe all local building and safety codes.
Unpack and inspect the products for any shipping damages. If you find damages, do not install.
Please note all products must be installed by a professional and certified plumber otherwise warranty might be voided.
sensor
Sensor Faucet Installations Instructions
Size:
Operating Pressure:
Minimum operating pressure 0.5 bar Maximum operating pressure 5 bar
Step 1:
Step 2:
sensor
Step 3:
Step 4:
Battery Box
Correct way for Hose
Specifications
Self Contained Design
Cupc,Wras,Nsf,Watermark,Ce
Electrical Sensor Kitchen Sink Basin Tap
Self Contained Design
Ceramic Mixing Valve Built-In
Wall Mount Design One Piece Infrared Sensor Basin Faucet
The Sensor Is Self-Adjusting To Its Installation Environment When Wired In
Mains And Battery Powered Options Included
Solid Brass Construction
Hygienic And Water Conservation
Technical Information
Power Supply
DC:6V(4 X AA Alkaline Batteries) AC:220V-240V/50Hz Or AC110V/60Hz
Power Consumption
Static≤0.3mW;Active≤3W
Battery Life
108000 Flushes(4 X AA Alkaline Batteries)
Sensor Field
5-30cm (Adjustable)
Water Pressure
0.05~0.8MPa
Ambient Temperature
0~55°C
Working Life
350000~400000 Times
Sensor Time
<1 Sec
Closing Time
<2 Sec
Low Voltage Indication
3.9V(The Light Will Flash Twice Each Two Seconds)
Self Shut Off Time
65-70 Sec (Non Stop Flushing)
For ease of installation, the faceplate and battery can be disconnected from the unit at the connectors. Faceplate and Spout
Remove the back connector from the spout. Push the connector through the hole in the faceplate and screw into the spout. Secure in position with the two fixing screws.
Make sure that the spout hole is in the 12 o’clock position and the spout is pointing downwards.
Note: Please do not install this product opposite or near any reflective surfaces as this may lead to false or permanent activation.
Before installing your new mixer, flush through the pipework to ensure removal of debris, turn off the water supply.
The valve must be set into the wall to depth of 80 mm.
If you are fitting the valve to a partition wall or a wall of particularly soft substrate you will need specialist fixings.
Select the position for the valve and offer the shower valve to the wall, mark the fixing points with a suitable pencil, there are 2 pre-drilled holes in the back of the unit. Remove the valve from the wall, drill the holes to a suitable depth for the wall plugs and secure with suitable screws Connect the flexible hose coming from the unit onto the spout, making sure that the rubber washer is in place. Sensor connections
Connect the plug coming from the valve unit to the socket coming from the sensor. Power connections
Connect the socket coming from the transformer to the plug coming from the sensor.
Battery connections
Undo the screw on the top and remove the lid. Insert the 4 batteries into the base, according to the diagram in the bottom of the base. Replace the lid making sure that the 2 springs are orientated to match the negative ends of the 2 batteries (right).
Connect the plug coming from the transformer to the socket coming from the battery.
Slide the two tabs in the top of the faceplate over the faceplate lip, and secure in position with the screw on the underside.
Please ensure that enough access is left for the screw to be removed/inserted, during any routine maintenance.
Turn on the water.
Flexible Connecting Hose Care must be taken when connecting the flexible connection hose from the power supply box to the spout to ensure it does not bend sharply and kink or twist. See above for recommended ways to fit the flexible connecting hose.
Important: Failure to follow these guidelines may result in poor performance and damage to the flexible connection hose.
Bravat In Wall Mount Brushed Nickel Commercial Electric Instant Water Heater Automatic Faucet
The Electrical Sensor Sink Basin Wall Mount Tap Is Specially Designed For Commercial Use, But It Can Be A Great Asset In Your Home As Well. It Is Hygienic - No Contact Between The Dirty Hands And The Handle, No Germ Contamination, Therefore No Possibility Of Disease Transfer. There Is No Risk To Forget It Running And This Faucet Will Never Drip, In The Long Run This Will Bring Great Water Cost Saving. The Sensor Range Of Action Can Be Adjusted To Best Suit Your Needs Between 5 And 30 Cm. There Are Many Choices Of Finish: Chrome, Gold, Or Brushed Nickel. Made Of The Best Materials, It Comes With A 1 Year Warranty.Ideal For Commercial Use Applications In Public Restrooms, Restaurants, Office Building, Public Facilities, Hospitals. Fits All Standard US Plumbing.
Features:
Type : Basin Faucets
Model Number : BST5061SB
Surface Treatment : Brushed
Number Of Handle :0
Chrome Plating : 24/48 Hours Salt Spray
Power Supply : DC,AC,AC+DC
Surface Finishes :Chrome,Gold, Brush, Nickle
Surface Finish : Brushed Nickel
Faucet Mount : Single Hole
Style : Contemporary
Approval : CE,WRAS,CUPC,ROHS,WATERMARK
Battery Lifespan : 108000 Flushes
Brand Name :Fontana Sensor Faucets
Feature :Sensor Faucets, Thermostatic Faucets, Electric Faucets, 2014 Electrical Sensor Kitchen Sink Basin Tap
