According to the template (B) mark the location of the mounting holes (1). Use a drill with a 6mm bit to drill mounting holes into studs or blocking.
Install the mounting brackets (C) with the tapping screws (D1). Thread the shower bars (E) onto the mounting brackets, and the inlet hose (F) onto the water inlet.
Step 3:
Step 4:
Attach the shower head (A) to the shower bars (E). Connect the inlet hose (F) to the showerhead.
Step 5:
Step 6:
Hand Held Shower Installation Instructions
Step 1:
hand shower
Step 2:
HAND HELD SHOWER
Hand Shower Outlet Installation • Complete the outlet pipework ensuring it ends in an appropriate 15mm x 1/2" BSP female thread elbow.
Note: This fitting is not supplied as variations in installations require the selection of a suitable solder or compression fitting.
• Install the 'Wall Outlet', thread long male 1/2" BSP into the appropriate female fitting using PTFE tape to give a watertight joint.
Note: The thread can be cut to size if required. Make sure that all debris is removed from the connector and the section that has been cut is dressed correctly, before installation.
Shower Body Jets Installation Instructions
Step 1:
Step 2:
body spray
Step 3: (Pressure Balancing Loop)
Rough-in Suggestion: This installation requires a 1/2" male threaded pipe fitting to extend 1/4" beyond the finished surface. The plumber should install a properly anchored 1/2" female pipe fitting (i.e. a drop-ear ell) recessed into the wall, into which a brass pipe nipple of proper length can be fitted once the finished wall is complete. Note: The hole size opening should be 1.5" max diameter. Bodyspray placement: Custom shower systems are sized to the user or users. Bodysprays are normally placed at the upper back, middle back, and upper thigh. Always position bodysprays according to the preferences of the user(s).
Pressure Balancing Loop: If installing bodysprays in a bank of 3 or fewer, a pressure balancing loop is not necessary. If installing bodysprays in a bank of 4 or greater, a pressure balancing loop must be used to keep the pressure even between the bodysprays.
Thermostatic Mixer Installation Instructions
Step 1:
Step 2:
Shower
Mixer
Shower Valve Mixer Installation Instructions
Step 3:
Step 4:
Please screw the handles out according to the above direction.
Take board and four handles out of the faucet body.
Shower Valve Mixer Installation Instructions
Step 5:
Step 6:
According to the actual size, get all pipe embedded mounts well ready.
According to the product basic size, dig four holes on the ideal place of the wall.
Shower Valve Mixer Installation Instructions
Step 7:
Step 8:
Place 4 tapping screws into the holes using a hammer.
Fix the faucet body by hand. And then take it into the four tapping screws.
Shower Valve Mixer Installation Instructions
Step 9:
Step 10:
Connect hot & cold supply water pipes (not provided) and other water pipes. After that, open the water to test if all pipes have leakage or not. At last, seal the wall.
Take the board onto the faucet body.
Shower Valve Mixer Installation Instructions
Step 11:
Step 12:
Screws the handles into the handwheels.
a. Each water function handwheel
b. Tempering handwheel
Fontana Lima Dark Oil Rubbed Bronze Massage Shower System
Turn your shower into a water and light show with this LED shower system. Comes complete with a shower head, a hand-held shower, and adjustable body jets - all with a beautiful warm bronze finish. Six adjustable body massage sprayers and a handheld shower provide you with all over coverage. The recessed rainfall showerhead is proportionally generous. Adding a touch of elegance to your bathroom, the LED lights will provide a visual water temperature indicator. Built-in hydro-powered device powers the LED lights, which provide visual shower temperature cues to reduce water waste. The lights will dim and brighten when you lower and raise the pressure so you can set the perfect mood, water, and lighting. When water temperature is ≤89 °F (≤32 °C), Blue color will show automatically. When water temperature is between 97 to 107 °F (36-42 °C), Green color will show automatically. When water temperature is between 109 to 122 °F (43-50 °C), Red color will show automatically. When water temperature is above 122 °F (>50 °C), Red color will flash immediately. The lights will dim and brighten when you lower and raise water pressure. Comes with solid brass mixer. Universal threading will fit any standard shower head by simply unscrewing the old one by hand and attaching the new one. S hower head is made out of stainless steel, so its made to last.
