Home > Installation Instructions For Fontana Liverpool Wall Mount Thermostatic Rainfall Shower Set System

How to install Fontana Liverpool Wall Mount Thermostatic Rainfall Shower Set System | FS-043S-RAINFALL-SHOWER-SYSTEM


Easy step by step Installation Instructions for Shower Set Visit Product Page

  • Before you begin, please read the installation instructions below. Observe all local building and safety codes.
  • Unpack and inspect the products for any shipping damages. If you find damages, do not install.
  • Please note all products must be installed by a professional and certified plumber otherwise warranty might be voided.
shower Fontana Liverpool Wall Mount Thermostatic Rainfall Shower Set System

Shower Head Installation Instructions


Size




Step 1: Round Shower Step 2:
Wall Mount Round Showerhead
Step 3: Step 4:
Step 5: Step 6:


1. Remove the old shower head by using the channel lock pliers or monkey wrench. Be sure to turn the pliers counter-clockwise to loosen the old shower head. (Tip: Right is tight, left is loose.)
2. Remove the shower arm by turning it by hand counter-clockwise.Make sure you remember to apply putty or tape to the new arm. (Tip: Using teflon tape is less messy)
3. Apply teflon tape to the threading of the shower arm by wrapping it around the threads, go all the way around 3 or 4 times depending on the quality of the Teflon tape.
4. Install the new shower arm by going clockwise by hand until it is tight, then put painters tape around the arm and tighten the arm with the channel lock or monkey wrench.
5. Place Teflon tape around the threads on the shower head and then place the shower head onto the shower arm by turning the shower head clockwise after the shower arm is already in the wall.





Hand Held Shower Installation Instructions


Size

Parts:

1. Wall Outlet
2. 60" Shower Hose With Gaskets
3. Complete Slide Bar With Mounting Parts / Posts, Screws & Anchors
4. Adjustable Shower Mount (Attached To Slide Bar)
5. Hand Held Shower

HandHeld Shower Installation Instructions Handshower
Installation Instructions
Supply Elbow Installation Wall Bar Installation
Step 1: Step 2:



Apply Plumber Tape To Threaded Ends Of 1/2" (13 Mm) Iron Pipe Nipple (Not Supplied) And Thread Into Shower Riser Elbow So That Nipple Extends Past The Finished Wall No More Than 0.2" (4.8 Mm) And No Less Than 1/16" (1.6 Mm). Place The Supplied Installation Gasket (1) Behind The Elbow (2). Screw The Supply Elbow Onto The Nipple Making Sure That The Supply Elbow Outlet Is In A Downward Facing Position. Minimum Diameter For Hole Is 1" (25 Mm) With A Maximum Of 1½” (38 Mm).

Caution: To Avoid Damage To The Supply Elbow Or Hose Finish During Installation, Wrap With A Cloth Or Tape And Use Only A Smooth-Jawed Wrench. DO NOT OVERTIGHTEN CONNECTIONS.
A. Select A Convenient Height To Place The Shower Rail Based On Your Personal Needs. Be Sure To Leave Enough Slack For The Hose Of The Hand Shower To Operate Freely When The Hand Shower Is Placed In The Extreme Up Or Down Positions. Note: If Possible It Is Recommended That The Slide Bar Brackets Be Secured Into The Wall Studs. For Ceramic Tile Installation, Drill Holes In Grout If Possible.

B. Mark The Place For Drilling The Hole For The Lower Post. Mark Using A Level, In A Vertical Line From The Lower Hole, The Placement Of The Upper Post Hole. Distance Approximately 25.7" (653 Mm).




Step 3: Step 4:


Note: Hole Size Will Be Determined By Your Use Of Just The Screw Or Anchor And Screw For Installation. Drill Hole For Mounting Of Bottom Post. Start With A Smaller Drill Bit Size, 1/8" Is Recommended, And Drill Hole. If You Hit A Wall Stud, Go To Next Step. If You Do Not Hit A Wall Stud, Change To A Drill Bit Size Suitable For The Anchors, 1/4" Is Recommended, And Re-Drill Hole.
Anchors Are For Use On Drywall Or Tile. For Fiberglass, Acrylic And Flat Plastic Surfaces, Use Toggle Bolts (Not Included).
Before Drilling Top Mounting Hole, It Is Recommended That You Place The Assembled Slide Bar And Post Assembly (1) On Its Side Next To The Hole Locations You Have Marked. Make Sure Posts Are Pressed Fully Onto Bar. Align Centre Of Bottom Post With Bottom Hole That Was Just Drilled And Make Sure Centre Of Top Post Aligns With Mark For Top Hole. If Not, Re-Mark Top Hole Location. If It Aligns, Drill Top Hole In Location As Marked.
Insert Anchors (1) Into Drilled Holes. Slide Covers (2) Over Brackets (3), And Insert Screws (4) Into Bracket/Cover Assembly. Secure Assembly To Wall With Screws.

Slide The Slide Mechanism (1) And Elbow (2) Onto The Wall Bar (3). Slide Wall Bar Over Bracket Tabs (4) And Secure The Wall Bar Unit With Screws (5) Provided. Install Caps (6) Into Ends Of Wallbar. Lower Elbow (7) & Screw (8) Was Pre-Installed Prior To Shipping, Tighten Screw (9) If You Find It Is Sliding Inside Bar.










Step 5: Step 6:


Connect The Shower Hose To The Wall Outlet (1) And The Hand Held Piece (2), Ensuring That The Internal Gaskets (3) Are Present In The Shower Hose Nuts. Normal 1/2" Rubber Gaskets Can Be Used.

Place The Conical Nut Of The Hose (4) That Is Connected To The Hand Held Piece, In The Slide Bar Holder (5) And Turn It To Desired Position.
To Slide The Mechanism Up Or Down, Push In On The Button (6) Of The Mechanism And Slide It On The Bar.








Step 7:


Care Should Be Given To The Cleaning Of This Product. Although Its Finish Is Extremely Durable, It Can Be Damaged By Harsh Abrasives Or Polish. To Clean, Simply Wipe Gently With A Damp Cloth And Blot Dry With A Soft Towel.
Maximum Flow Rate: 2.5 GPM















Tub Spout Installation Instructions

Step 1: Step 2:
Hand Held
Shower
Hand
Held
Shower


Step 3: Step 4:
Hand Shower



Shower Thermostatic Mixer Installation Instructions




      Shower
      Mixer

      Thermostatic Mixer Installation Instructions


      Step 1:Step 2:

      Thermostatic
      Mixer

      Thermostatic Mixer
      Step 3:Step 4:
      Thermostatic Mixer
      Step 5:Step 6:
      Thermostatic Mixer
      Step 7:Step 8:

      Thermostatic Mixer







      Fontana Liverpool Wall Mount Thermostatic Rainfall Shower Set System


      Give your bathroom an elegant glance with a rain shower rainfall mixer shower set. Three lever control bathroom shower in chrome finish is the perfect complement to today's modern home. This FontanaShower is ceiling mount complete shower head, handheld shower mixer set provides a luxurious showering experience and is the perfect complement to any modern bathroom. The modern design handheld shower, cold and hot water shower mixer and an easy-to-use mixer valve, made from high-quality. Be sure, when it comes to new bathroom rain shower sets, FontanaShowers is offering shape, finish, and styles you're looking for. Optional LED visual water temperature cue available. Built-in hydro-powered device powers the LED lights, which provide visual shower temperature cues to reduce water waste. The lights will dim and brighten when you lower and raise the pressure so you can set the perfect mood, water, and lighting. When the water temperature is ≤89 °F (≤32 °C), the Blue color will show automatically; When the water temperature is between 97 to 107 °F (36-42 °C), the Green color will show automatically; When the water temperature is between 109 to 122 °F (43-50 °C), Red color will show automatically; When the water temperature is above 122 °F (>50 °C), Red color will flash immediately.

      Features:

      Visit Product Page
      • Brand Name: FontanaShowers
      • Model Number: FS-043S-RAINFALL-SHOWER-SYSTEM
      • Water Outlets: Handheld Shower, Shower Head
      • Hot & Cold: Yes
      • Surface Finish: Chrome
      • Style: Contemporary
      • Valve Core Material: Brass
      • Number of Handles: 3 Handle
      • Type: Bath & Shower
      • Shower Valve: Triple Concealed, Brass, Square Plate
      • Features: Pre-set maximum temperature (38°), Automatic anti-scald device
      • Installation: Wall Mount
      • Shower Head Size: 8", 10", 12"
      Fontana Liverpool Wall Mount Thermostatic Rainfall Shower Set System