Home > Installation Instructions For Fontana Sète Remote Controlled Stainless Steel LED Smart Music Rainfall Thermostatic Shower Head With Massage Jets And Hand Sprayer In Matte Black

How to install Fontana Sète Remote Controlled Stainless Steel LED Smart Music Rainfall Thermostatic Shower Head With Massage Jets And Hand Sprayer In Matte Black | FS1462


Installation Instructions for Bathroom Shower Set Visit Product Page

  • Before you begin, please read the installation instructions below. Observe all local building and safety codes.
  • Unpack and inspect the product for any shipping damages. If you find damages, do not install.
  • Please note all products must be installed by a professional and certified plumber otherwise warranty might be voided.
shower Fontana Sète Remote Controlled Stainless Steel LED Smart Music Rainfall Thermostatic Shower Head With Massage Jets And Hand Sprayer In Matte Black



Shower Head Installation Instructions



Step 1: recessed Step 2:



Step 3: Step 4:


Step 5: Step 6:



Step 7: (LED Control Box) Step 8:












Spout & Hand Held Shower Installation Instructions





Step 1: Step 2:
HandHeld
Shower
Hand
Held
Shower

Handheld Shower
Step 3:


Hand Shower Elbow Installation

• Complete the outlet pipework ensuring it ends in an appropriate 15mm x 1/2" BSP female thread elbow.
Note: This fitting is not supplied as variations in installations require the selection of a suitable solder or compression fitting.

• Install the 'Wall Outlet', thread long male 1/2" BSP into the appropriate female fitting using PTFE tape to give a watertight joint.
Note: The thread can be cut to size if required. Make sure that all debris is removed from the connector and the section that has been cut is dressed correctly, before installation.

1. Attach the escutcheon to the supply elbow.
2. Apply Teflon tape to the threaded tailpipe of supply elbow.
3. Screw the supply elbow into the female fitting of water supply.
4. Press the escutcheon against the finished wall.


Hand Shower Wall Bracket Installation

Decide the position for the shower head holder on the wall within the bath showering area and proceed as follows:
• Hold the hand shower head holder fixing plate in a suitable position on the wall, mark out the position of the holder. Mark the two locating holes.
• Drill and plug the wall. Use an appropriate masonry drill, but if the wall is plasterboard or a soft building block, use special wall plugs and an appropriate drill bit.
• Slide the inserts onto the screws in the orientation. Secure the inserts by tightening the screws.
• Slide the hand shower head holder body onto the inserts and secure by tightening the grub screw facing down.









Shower Body Jets Installation Instructions



Step 1:
Step 2:
body spray


Step 3: (Pressure Balancing Loop)





Rough-in Suggestion:
This installation requires a 1/2" male threaded pipe fitting to extend 1/4" beyond the finished surface. The plumber should install a properly anchored 1/2" female pipe fitting (i.e. a drop-ear ell) recessed into the wall, into which a brass pipe nipple of proper length can be fitted once the finished wall is complete.
Note: The hole size opening should be 1.5" max diameter.

Bodyspray placement:
Custom shower systems are sized to the user or users. Bodysprays are normally placed at the upper back, middle back, and upper thigh. Always position bodysprays according to the preferences of the user(s).

Pressure Balancing Loop:
If installing bodysprays in a bank of 3 or fewer, a pressure balancing loop is not necessary.
If installing bodysprays in a bank of 4 or greater, a pressure balancing loop must be used to keep the pressure even between the bodysprays.





Instructions
Body jets should be arranged in your system to provide the necessary spray outlets to suit the application.
1. Identify all components and check for completeness, particularly before arranging fitting.
2. Depending on the application the body jet can be panel mounted using a backnut (not supplied) or set into the wall on rigid pipe work. If panel mounting care should be taken to ensure connection can be made after securing with the backnut.
3. Connect body jet to pipe work using recommended ½” BSP connections (not provided) with thread sealing compound where necessary.
Note: - Before finishing wall turn on water supplies to check both correct system function and for leaking from joints/connections.
4. Complete wall finish.




Shower Thermostatic Mixer Installation Instructions




Step 1:Step 2:
MixerValve


Mixer Control Valve Installation Instructions
Step 3:Step 4:


Mixer Control Valve Installation Instruction
Step 5:Step 6:

Mixer Control Valve Installation Instruction
Step 7:



- Release Six handwheel levers according to the above directions.
- Take apart the embed valve, panel, and handwheel.
- Dig the embed space for the pipe on the wall according to the specification of the valve.
- Dig 4 holes according to the position of the screws.
- Use a hammer to thwack the screws into 4 holes.
- Fix the valve body with 4 screws.
- Find out the expansion screw heads with washer and spring washer. Use copper sleeve wrench to lock the screw heads with the embed valve body.
- After connecting all the pipes and before sealing the wall with concrete, confirm no leaking problem occur when you turn on the water.
- Fix the decorative panel on the embedded valve body.
- Screw the handwheel arms with the handwheels.












Fontana Sète Remote Controlled Stainless Steel LED Smart Music Rainfall Thermostatic Shower Head With Massage Jets And Hand Sprayer In Matte Black


The Fontana Sète Remote Controlled Stainless Steel LED Smart Music Rainfall Thermostatic Shower Head with Massage Jets and Hand Sprayer in Matte Black is perfect to complement today's modern home. This Smart LED Musical Shower Set was designed to bring a modern and fun feel into any bathroom. Built from premium materials and finished with elegance. You may even have more time to enjoy your shower with a rainfall feeling. Easy-to-install and leak-free. The design was inspired by the FontanaShowers. Be sure, when it comes to new bathroom sink faucets, FontanaShowers is offering shape, finish and styles you're looking for.

Features:

  • Brand Name: FontanaShowers
  • Model Number: FS1462
  • Feature: LED Musical Shower Head
  • Style: Contemporary
  • Installation Type: Ceiling Mount
  • Cold/Hot Control: Auto-Thermostatic Control
  • Type: Fixed Support Type
  • Smart Device: Yes
  • Finish: Matte Black
  • Surface Finishing: Stainless Steel
  • Valve Core Material: Brass
  • Surface Treatment: Blackened
  • Shower Head Material: 304 Stainless Steel
  • Thread: G1/2"
  • Hose Length: 1.5m
  • Water Flow: 16 L/min ~ 28 L/min
  • Music: Bluetooth Connection
  • Shower Head Size: 800 * 600 mm
  • Minimum Water Pressure Requirement: 0.3MPA
  • Fontana Sète Remote Controlled Stainless Steel LED Smart Music Rainfall Thermostatic Shower Head With Massage Jets And Hand Sprayer In Matte Black


    Fontana Showers Installation Instructions