Home > Shower Set With Valve Mixer Two Way Concealed Wall Mounted Installation Instructions

Bravat Light Oil Rubbed Bronze Thermostatic Shower Set With Valve Mixer 2-Way Concealed Wall Mounted

The Bravat Light Oil Rubbed Bronze Shower Set With Thermostatic Valve Mixer -Way Concealed Wall Mounted is one of the most trendiest finishes across decor styles in the bathroom. It has a contemporary style with a beautiful LightOil Rubbed Bronze finish. When it comes to new bathroom upgrades, FontanaShowers is offering shape, finishes and styles that you've looking for.

Bravat Light Oil Rubbed Bronze Shower Valve Mixer 2-Way Concealed Wall Mounted Features:

Brand Name: FontanaShowers

Model Number: FS1067

Type: Shower Set & Shower Mixer

Style: Contemporary

Type: Fixed Support Type

Surface Finish: Light Oil Rubbed Bronze

Installation Type: Wall Mount

Control Type: Single Holder Dual Control

Size: 7.91"-11.85" (201-300mm)

Surface Treatment: Polished

Valve Core Material: Ceramic

Bath Shower Type: In-Wall Shower Mixer

Valve Type: Ceramic Valve

Faucet Handle Material: Zinc Alloy

Mixer Body Material: Brass

Valve Included: Yes

Embedment Depth: 2.16" (55mm)

Valve Panel Dimension: 6.29"x6.29" (160x160mm)

Connector: G1/2"B (Standard)

wall mounted valve box, how to install a concealed shower mixer valve, concealed shower installation, mixer shower surface mounted pipes, concealed shower arm fitting instructions, flush shower valve

Bravat Light Oil Rubbed Bronze Shower Set With Valve Mixer 2-Way Concealed Wall Mounted

FontanaShowersÂ®Product Warranty Information

Before you begin, please read the installation instructions below. Observe all local building and safety codes.

Unpack and inspect the product for any shipping damages. If you find damages, do not install.
Please note all showers must be installed by a professional and certified plumber otherwise warranty might be voided

shower

Shower Head Installation Instructions

Specifications	Shower
		1w
Step 1		Step 2
Step 3		Step 4

Turn water on for 1 minute to flush any debris. Wrap shower arm (H) threads with Teflon tape (I). Install the shower arm (H) into shower outlet through cover plate (J). Then, add a rubber washer (K) and attach shower head (L) to shower arm (H).

Hand-Held Shower Installation Instructions

Step 1	mixer	Step 2
Step 3		Step 4
Step 5		Step 6

1. GATHER ALL PARTS

2. HOLE LOCATIONS FOR WALL MOUNT: Remove Front Cover (A) from Wall Mount (B). Use Wall Mount Screw Holes (C) to place the desired location. Using a punch or awl, tap the screw hole locations.Holes must be vertically aligned.

3. ANCHOR INSTALLATION: Drill two 1/4” dia. Holes (A). If installing into a studs drill two 1/8” dia. holes and do not use Anchors (B). Insert Anchors (B) into Holes (A) and tap flush with the wall.

4. WALL MOUNT INSTALLATION: Place Wall Mount (A) into wall and inset Mounting Screws (B) through Wall Mount Holes (C) and tighten until Wall Mount (A) is flush with the wall. Do Not Over Tighten! Insert Front Cover (D) into Wall Mount (A)

5. DROP ELBOW & HOSE INSTALLATION: Apply PTFE plumbers tape on both ends of Pipe Nipple (A) (not included). Screw Pipe Nipple (A) into the elbow inside the wall.The Pipe Nipple (A) is to project 1/4” – 3/4” from the finished wall. Screw Drop Elbow (B) onto Pipe Nipple (A) and tighten until Drop Elbow (B) is property positioned and flush to the finished wall. Place Rubber Seal (C) inside Hex Hose Fitting (D). Connect Hex Hose Fitting (D) into Drop Elbow Outlet (E) by turning Hex Hose Fitting (D).

6. UNIT STARTUP: Turn on hot and cold water supplies, and check all connections for leaks.

7. FINAL FLUSHING: For final flushing, turn the valve on and allow water to run through the Hose (A) for several minutes.Allow water to run for several minutes until all foreign matter clears the line.

8. SHOWER ARM INSTALLATION: Place Rubber Seal (A) inside Tapered Hose Fitting (B). Conned Hand Shower (C) to Hose (D) by turning Tapered Hose Fitting (B ) clockwise.Warning: Make sure Hand Shower (C) is securely tightened to Hose (D).

Thermostatic Mixer Installation Instructions

Step 1	mixer	Step 2	mixer	Step 3
Step 4		Step 5		Step 6

Step 7

Basic-size, according to the embedded box to open the hole on solid wall, should consider installing the metope of the distance between 60-75mm, for example, after blank wall in the shop, the ceramic tile surface to increase the thickness of the 20 mm, so PiQiang in the depth of the hole should be chosen 40 to 55 mm.
Hole bottom should remain flat so that subsequent adjustment embedded box of vertical and horizontal convenient installation for the principle
Pay attention to the direction of the up and down or so embedded box, on the left by hot water pipes, right after the cold water pipes, pick up and down the mixed water pipes.
After the pipe connection, according to the pipeline arrangement, and open the corresponding channel slot tube in the blank wall.
Embedded box fixed before, to embed box and trial test and pipe water clean connection pipe, and test before mixing water channels should be open.
Test, before opening the switch valve core, open the water to test around inlet pipe, is connected closely with no leakage and the water pipe test after dosing open state, whether to test on the mixed water pipe connection without leakage. At the same time clean tube foreign bodies in case of influencing water control valve function.
It will be embedded in a box into the solid wall with a self-tapping screw that is fixed on the wall.
With parallel ruler for correction of the embedded box of horizontal and vertical direction to embed box into a level with the ground and metope as 90°. In the absence of good correction will influence the control panel installation effect.

Step 8:		Step 9:
	Mixer		Mixer
Once again confirm the pipe connection is correct, try no leakage, water shower other embedded with the packing box and pipe joint is fixed Solid wall embedded box is installed, laid our behind the wall can be a follow-up control valve installation		The lying of the wall not to embed box is open, lest the box into the packing after solidification effect of control valve installation Control valve set surface for plating and smooth surface should be kept inside the original packaging before installation to prevent scratches, corrosion, and lost.

Step 10:

1. Laid metope ceramic tile or another adornment metope, keep the metope smooth, with the embedded box into 90″ vertically
2. Along with the embedded highlights, the glass on the edge glue, embedded box to improve waterproof performance prolongs service life.

Step 11:

3. Cut oof using a cutting tool embedded box of highlightings, keep away from the wall 2-4mm highly advisable.
4. Try yo remove embedded lifted the lid plate and water components

Step 12:

5. Installed control panel, check on panel hole protecting glue before the set cut, such as unprotected glue set directly into the panel is easy to scratch panel
6. Install the switch handle, with packing with small hexagonal wrench clockwise to switch handle is fixed on a main valve spool control valve in, install decorative rubber plugs.