Fontana Automatic Soap Dispensers™ | Architectural and Engineering Resource
Fontana Elysian Dispense Champagne Touchless Automatic Soap Dispenser:
Overall Product Dimensions
This dimensional drawing resource is intended to support architects, plumbing
engineers, interior designers, contractors, installers and facility managers
coordinating the Fontana Elysian Dispense FS9840CP wall-mounted automatic soap
dispenser within commercial washrooms. The drawing package communicates the
dispenser’s front elevation, side elevation, top plan view, wall flange,
spout projection, soap discharge outlet, infrared sensor, concealed motor and
controller case, and principal dimensions in metric and imperial units.
Fontana Elysian Dispense Champagne Touchless Automatic Soap Dispenser
The Fontana Elysian Dispense FS9840CP is a commercial-grade,
wall-mounted automatic liquid soap dispenser designed for hygienic
hands-free operation. Its rectangular champagne-finish spout provides
a streamlined architectural appearance, while the motor, controller
and one-liter soap reservoir remain concealed behind or below the
finished wall.
-
Model:
FS9840CP
-
Installation:
Wall mounted
-
Finish:
Champagne
-
Material:
Solid brass construction
-
Dispenser type:
Automatic liquid soap dispenser
-
Soap capacity:
1 liter
-
Power:
AC 110–240V, 50/60Hz
-
Sensor:
Infrared touchless activation
-
Spout projection:
220 mm (8-21/32")
-
Spout dimensions:
40 × 20 mm
-
Wall flange:
60 × 60 mm square
-
Motor case:
307 × 90 × 106 mm
Required Overall Product Dimension Drawing Package
Each drawing should use a consistent scale, dimension style and product
identification block. Measurements should be referenced from the finished
wall surface, wall-flange face and dispenser centerline. Drawings should
also identify the spout projection, spout section, soap discharge outlet,
infrared sensor, recommended wall opening and concealed motor or
controller case. Metric and imperial dimensions should be shown together
for architectural, MEP and international project coordination.
Overall Product Dimensions
Shows the complete dimensional arrangement of the Fontana Elysian
Dispense FS9840CP, including the exposed wall-mounted spout,
square wall flange, front elevation, side elevation, top plan
view, spout-end view, concealed motor case and soap reservoir.
This drawing provides contractors and design professionals with
an overall dimensional reference before reviewing the individual
views.
Front Elevation
Displays the dispenser as viewed directly by the user. The front
elevation identifies the 60 mm square wall flange, 40 mm spout
width, outlet position and dispenser centerline. This view helps
designers maintain consistent alignment with the lavatory,
faucet, mirror and adjacent washroom accessories.
Side Elevation
Illustrates the complete horizontal projection from the finished
wall to the forward end of the dispenser. The side elevation
identifies the 220 mm spout projection, 20 mm spout height and
soap discharge outlet located beneath the forward section of the
spout.
Top or Plan View
Defines the dispenser footprint and its horizontal relationship
to the finished wall and lavatory centerline. The plan view
identifies the 40 mm spout width, 60 mm wall-flange width and
infrared sensor location near the forward end of the dispenser.
Spout Projection and Section
Identifies the principal exposed dimensions of the rectangular
spout. The horizontal projection measures 220 mm
(8-21/32 inches), while the spout section measures 40 mm wide
by 20 mm high. These dimensions should be coordinated with the
selected basin and finished-wall assembly.
Wall Flange Dimensions
Documents the square exposed wall flange and the recommended
wall opening. The flange measures 60 × 60 mm
(2-3/8 × 2-3/8 inches), and the recommended circular wall
opening is approximately 35 mm (1-3/8 inches) in diameter.
Confirm the final opening before cutting tile, stone or finished
wall panels.
Soap Discharge and Sensor Location
Pinpoints the soap discharge outlet on the underside of the
forward spout section and identifies the infrared sensor near the
spout end. The outlet should be positioned over the usable basin
area, while the sensor detection zone should remain clear of the
basin rim, backsplash and reflective accessories.
Concealed Motor and Controller Case
Presents front, side and top views of the concealed operating
case. The motor and controller enclosure measures approximately
307 mm high × 90 mm wide × 106 mm deep
(12-3/32 × 3-35/64 × 4-11/64 inches). Sufficient concealed
clearance should be provided for the case, tubing, wiring and
maintenance access.
Engineering note:
All dimensions are nominal and the drawing should not be scaled.
Final measurements, mounting locations, wall openings, concealed
clearances and service requirements should be verified using the
approved FontanaShowers specification sheet, installation instructions
or project submittal package before wall penetrations and service
locations are established.
Architectural and MEP Coordination Considerations
Lavatory Alignment
Position the 220 mm projecting spout so the soap discharge outlet
is located over the basin’s usable capture area and does not
dispense onto the countertop, backsplash or front rim.
Accessible Reach
Coordinate the wall-flange elevation, spout projection, outlet
location and sensor activation area with the accessible lavatory
and applicable reach-range requirements.
Service Access
Preserve access to the concealed motor and controller case,
one-liter soap reservoir, pump, tubing and electrical connections
without requiring removal of permanent wall finishes.
Power Coordination
Coordinate the AC 110–240V, 50/60Hz power supply, transformer,
concealed wiring route and service location with the electrical
drawings and locally adopted electrical requirements.
Sensor Clearance
Keep the infrared detection area clear of projecting basin rims,
shelves, accessories and highly reflective surfaces that could
interfere with reliable touchless activation.
Reservoir and Motor Position
Install the soap reservoir and concealed 307 × 90 × 106 mm motor
case in an accessible service area with adequate clearance for
refilling, inspection, tubing maintenance and component
replacement.
FontanaShowers Installation and Specification Resources
FS9840CP Product Page
Product information, technical details, finish information and
available documentation for the Fontana Elysian Dispense
Champagne Touchless Automatic Soap Dispenser.
Wall-Mounted Dispenser Installation Guide
Installation, rough-in, commissioning, cleaning and maintenance
guidance for wall-mounted commercial automatic soap dispensers.
FontanaShowers Installation Hub
Central installation resource for automatic soap dispensers,
touchless faucets and other FontanaShowers commercial fixtures.
Automatic Soap Dispenser Collection
Explore related wall-mounted, deck-mounted and commercial
automatic soap-dispenser configurations and finish options.
Automatic Soap Dispenser BIM Files
BIM and architectural coordination resources for automatic
soap-dispenser planning, documentation and multidisciplinary
project coordination.
Automatic Dispenser Installation Resource
General setup information covering automatic operation, concealed
components, power supply, commissioning and maintenance
considerations.
Professional Engineering and Accessibility References
Project verification:
Overall product dimension drawings are coordination tools and do not
replace approved project submittals. The architect, engineer and licensed
installer should verify final dimensions, finished-wall construction,
mounting support, wall opening, basin alignment, concealed motor-case
clearance, electrical requirements, accessibility criteria and locally
adopted codes before installation.
|
|
|
