Fontana Automatic Soap Dispensers™ | Wall Rough-In Drawing
Fontana Elysian Dispense Champagne Touchless Automatic Soap Dispenser:
Wall Rough-In Drawing
This wall rough-in drawing resource is intended to support architects, plumbing
engineers, electrical engineers, interior designers, contractors, installers and
facility managers coordinating the Fontana Elysian Dispense FS9840CP automatic
soap dispenser before finished wall surfaces are installed. The drawing package
should identify the spout centerline, finished-wall reference line, countertop
reference line, wall penetration location, verified wall opening diameter,
mounting-hole pattern, electrical conduit opening, soap-tube opening, controller
and reservoir position, and required backing or blocking.
Fontana Elysian Dispense Champagne Touchless Automatic Soap Dispenser
The Fontana Elysian Dispense FS9840CP is a wall-mounted commercial automatic
liquid soap dispenser designed for hands-free restroom operation. The rough-in
drawing is used during framing and MEP preparation to establish the required
wall penetrations, mounting support, concealed controller location and soap
reservoir placement before tile, stone, paneling or other finish materials
are installed.
- Model: FS9840CP
- Installation: Wall mounted
- Finish: Champagne
- Material: Solid brass construction
- Dispenser type: Automatic liquid soap dispenser
- Soap capacity: 1 liter
- Power: AC 110–240V, 50/60Hz
- Sensor: Infrared touchless activation
- Wall opening: Verify before wall finish installation
- Mounting support: Backing or blocking required
- Concealed components: Controller, pump and soap reservoir
- Application: Commercial and institutional restrooms
Required Wall Rough-In Drawing Package
Each drawing should use a consistent scale, dimension style and product
identification block. Measurements should be referenced from the finished-wall
line, dispenser centerline, countertop line and concealed service zone.
Drawings should also clearly distinguish the wall-mount spout from the concealed
controller, reservoir, tubing and electrical elements. The rough-in package is
intended to guide framing, wall blocking, penetrations, conduit preparation and
service coordination before final wall finishes are applied.
Standard Wall Rough-In Drawing
Shows the complete pre-finish construction arrangement for the Fontana
Elysian Dispense FS9840CP, including the spout location, finished-wall
reference line, centerline, mounting support, penetration points, conduit
entry, soap tube route, concealed controller and reservoir position. This
drawing provides the contractor with the overall rough-in reference before
reviewing the individual coordination views.
Spout Centerline
Identifies the horizontal and vertical centerline for the dispenser spout
relative to the lavatory and countertop. The centerline should be used to
coordinate the final dispenser position with the sink capture area, faucet,
mirror and other wall-mounted restroom accessories.
Wall Penetration Location and Verified Opening Diameter
Defines the exact penetration point through the wall for the dispenser
body and concealed connections. The drawing should indicate the verified
opening diameter required by the approved submittal and confirm that the
opening is coordinated before tile, stone or solid-surface finishes are
cut or installed.
Mounting-Hole Pattern
Shows the spacing and arrangement of mounting holes or attachment points
required to secure the wall-mounted dispenser assembly. This view should
be coordinated with the wall substrate and any internal reinforcing
required to support the fixture properly.
Electrical Conduit Opening
Indicates the location reserved for the power connection and electrical
conduit route serving the dispenser controller or transformer. The opening
should be coordinated with the electrical drawings, concealed wall
construction and locally adopted electrical requirements.
Soap-Tube Opening
Identifies the opening and pathway required for the soap supply tube
between the wall-mounted dispenser spout and the concealed soap reservoir
or pump assembly. The tube route should avoid sharp bends, pinch points
and conflicts with framing or other concealed services.
Controller and Reservoir Position
Documents the recommended concealed location of the controller, pump and
soap reservoir. This portion of the drawing should preserve adequate
service clearance for refilling, inspection, tubing connection, electrical
access and future maintenance.
Finished-Wall, Countertop and Blocking References
Shows the finished-wall reference line, countertop reference line and the
required backing or blocking behind the wall assembly. These references are
critical for aligning the dispenser with the lavatory while ensuring the
wall structure can support the mounting hardware and concealed assembly.
Engineering note: Do not establish rough-in locations from
estimated dimensions or unverified sketches. Final wall penetrations, opening
diameters, hole locations, conduit paths, tube routes and backing positions
should be taken from the approved FontanaShowers specification sheet,
installation instructions or project submittal package before wall framing and
finishes are completed.
Architectural and MEP Coordination Considerations
Finished-Wall Build-Up
Coordinate the rough-in depth with tile, stone, wall panel or other
finished-wall materials so the exposed spout and wall flange align
properly after finish installation.
Countertop and Lavatory Reference
Use the countertop and lavatory reference lines to align the spout
centerline over the basin’s usable capture area and to avoid soap
discharge onto adjacent finished surfaces.
Backing or Blocking
Provide suitable internal backing or blocking at the rough-in stage so
the wall-mounted dispenser assembly can be securely fastened without
compromising the wall finish system.
Electrical Coordination
Confirm the electrical conduit opening, transformer location and wiring
path with the electrical drawings before the wall is closed, and verify
service access for future maintenance.
Soap Reservoir Access
Locate the controller and soap reservoir where they remain accessible for
refilling, cleaning and inspection, and avoid placing them behind
permanent finishes with no service opening.
Concealed Service Clearance
Preserve sufficient space for tubing, pump connections, controller body
and maintenance reach so concealed services are not crowded by framing,
plumbing lines or other equipment.
FontanaShowers Installation and Specification Resources
FS9840CP Product Page
Product details, technical specifications, finish information and
available documentation for the Fontana Elysian Dispense champagne
touchless automatic soap dispenser.
Wall-Mounted Dispenser Installation Guide
Installation, rough-in, commissioning, cleaning and maintenance
guidance for wall-mounted commercial automatic soap dispensers.
FontanaShowers Installation Hub
Central installation resource for automatic soap dispensers,
touchless faucets and other FontanaShowers commercial fixtures.
Automatic Soap Dispenser Collection
Explore related wall-mounted, deck-mounted and commercial automatic
soap-dispenser configurations and finish options.
Automatic Soap Dispenser BIM Files
BIM and architectural coordination resources for automatic soap
dispenser planning, documentation and multidisciplinary project
coordination.
Automatic Dispenser Installation Resource
General setup information covering automatic operation, concealed
components, power supply, commissioning and maintenance
considerations.
Professional Engineering and Accessibility References
Project verification: Wall rough-in drawings are coordination
tools and do not replace approved project submittals. The architect, engineer,
electrical contractor, plumbing contractor and licensed installer should verify
final wall construction, finished-wall thickness, centerlines, mounting support,
wall penetrations, conduit openings, tubing routes, controller location,
reservoir access, accessibility criteria and locally adopted codes before
construction proceeds.
|
|
|
