Home > Installation Instructions for Oceane Bathtub Faucet

Oceane Chrome Finish Double Handle Bathtub Faucet

The Océane Bathtub Faucet comes in Chrome Finish. The Faucet is having Double Handle. With a modern design, the Océane bathtub faucet is original and eye-catching. The twist handles and the bright chrome finish make it ideal for contemporary bathrooms. It can be used either for the bathtub or the bathroom sink. It is deck mount and it requires three hole installation, with separate handles for hot and cold water. The design was inspired by the FontanaShowers design. Be sure, when it comes to new Bathtub Faucet, FontanaShowers is offering shape, finish and styles you're looking for.

Oceane Chrome Finish Double Handle Bathtub Faucet Features:

  • Brand Name: FontanaShowers
  • Model Number: FS142ACF
  • Faucet Type: Bathtub Faucet
  • Faucet Height: 8 5/8"
  • Spout Height: 7 5/8"
  • Spout Reach: 5 11/16"
  • Flow Rate: 2.4 GPM at 20 PSI
  • Design: Twist
  • Faucet Body Material: Brass
  • Faucet Finish: Chrome
  • Number of Holes: Three hole
  • Installation Type: Deck Mount
  • Oceane Chrome Finish Double Handle Bathtub Faucet

    FontanaShowers® Product Warranty Information FontanaShowers Product Warranty

    • Before you begin, read the installation instructions below. Observe all local building and safety codes.
    • Unpack and inspect the product for any shipping damages. If you find damages, do not install it.If you need assistance or have questions while installing your shower set, contact Customer Service.
    • We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures, and plumbing.


    • Screwdriver
    • Teflon Tape

    1. If your faucet comes with the brass T attached to the faucet body, unthread and remove the T and associated
    2. Thread the silver mounting washer and rubber sealing gasket on the faucet body.
    3. Apply a bead of silicone sealant to the underside of the spout, or faucet base, and thread through the center
    mounting hole.
    4. Thread the mounting hardware and brass T onto the spout pipe and hand-tighten to secure.
    5. Check to make sure the faucet is properly aligned and adjust as needed. When the faucet is in the proper position,
    finish tightening mounting hardware with your adjustable wrench.
    Tip: Make sure that the T outlets are aligned at an angle to allow maximum clearance for water connections.
    6. Wipe away any excess sealant around the faucet base using your damp cloth.
    7. Assemble the handles by screwing the lock nuts down to the end of the handle bodies. If handles are assembled
    move on to step 8.
    8. Insert the handle bodies up through the mounting holes. Thread the plastic slip washers and rubber sealing gaskets
    onto the handle bodies to secure.
    9. Hand tighten to attach the hot and cold flexible water feed tubes to the handle bodies and brass T. Give a ¼ turn with
    pliers or wrench, but don’t overtighten. (Hot water is always on the left and cold water is always on the right.) Curve
    tubes as necessary to ensure there are no kinks or knots.
    10. Place the handle assemblies on the handle bodies. Make sure that both handles are in the OFF position and tighten
    the set screw on the top or side of the handle with Allen wrench (provided).
    11. Connect the main water supply to the faucet body.
    12. To install the new pop-up drain, apply a bead of silicone sealant to the underside of the drain flange and place it in the mounting hole. If there is no pop-up drain, move on to step 16.
    13. Thread the lock nut onto the drain pipe and tighten with your adjustable wrench.
    14. Wipe away any excess sealant around the drain using your damp cloth.
    15. Push the pop-up rod down through the faucet body. Attach the pop-up rod to the pivot rod with the extension rod.
    Adjust the rods so that the drain stopper opens and closes properly.
    16. Attach the P trap to the drain pipe and wall drain fitting and tighten the locknuts.
    17. When your faucet installation is complete, turn on the water supply. Check to make sure that all connections are tight
    (no water should be leaking) and that the hot and cold supplies are working correctly. Turn the water on and allow
    the water to flow through the spout for approximately 60 seconds.

    Bravat Chrome Finish Dual Handle Bathroom Sink Faucet

    Bravat Chrome Finish Dual Handle Bathroom Sink Faucet

    BathSelect Ancient Round Antique Rainfall Wall ShoweBathSelect Ancient Round Antique Rainfall Wall Shower Head Installation Instructions Head Installation Instructions