Fontana Lima Rainfall Waterfall Oil Rubbed Bronze Shower System
Turn your shower into a water and light show with this LED Rainfall Waterfall shower system. Comes complete with a showerhead, a hand-held shower, and adjustable body jets - all with a beautiful warm bronze finish. Six adjustable body massage sprayers and a handheld shower provide you with all-over coverage. The recessed Rainfall Waterfall showerhead is proportionally generous. Adding a touch of elegance to your bathroom, the LED lights will provide a visual water temperature indicator. Built-in hydro-powered device powers the LED lights, which provide visual shower temperature cues to reduce water waste. The lights will dim and brighten when you lower and raise the pressure so you can set the perfect mood, water, and lighting. When the water temperature is ≤89 °F (≤32 °C), the Blue color will show automatically; When the water temperature is between 97 to 107 °F (36-42 °C), the Green color will show automatically; When the water temperature is between 109 to 122 °F (43-50 °C), Red color will show automatically; When the water temperature is above 122 °F (>50 °C), Red color will flash; When water temperature is above 122 °F (>50 °C), Red color will flash immediately.
Fontana Lima Rainfall Waterfall Oil Rubbed Bronze Shower System Features:
- Brand Name: FontanaShowers
- Model Number: FS-892RB
- Material: Solid Brass
- ShowerheadFinish: Dark Oil Rubbed Bronze
- Style: Contemporary Rain Showerhead
- Showerhead Height (thickness): 0.33"
- Showerhead Width: 14"
- Showerhead Length: 20"
- LED Power Source: Water Flow
- LED Color: Available without color-changing or with LED colors Blue, Green, Red
- Mount Method: Recessed Ceiling Mount
- Connection: 1/2" US standard (included)
- Body Jets: 360° Adjustable Body Jets
- Body Jets size: 5" x 5"
|
|
FontanaShowers®Product Warranty Information
- Before you begin, please read the installation instructions below. Observe all local building and safety codes.
- Unpack and inspect the product for any shipping damages. If you find damages, do not install.
- Please note all showers must be installed by a professional and certified plumber otherwise warranty might be voided.
|
shower
|
|
|
Shower Head Installation Instructions
Hand-Held Shower Installation Instructions
|
Step 1:
|
|
Step 2:
|
|
Step 3 & 4:
|
|
Hand
Held
Shower
|
|
Hand
Held
Shower
|
|
|
Handheld Shower
|
|
Handheld Shower
|
|
Handheld Shower
|
|
Step 5:
|
|
Step 6 & 7:
|
|
Step 8:
|
|
|
|
|
|
1. Gather All Parts
2. Hole Locations For Wall Mount
Remove Front Cover (A) from Wall Mount (B). Use Wall Mount Screw Holes (C) to place the desired location. Using a punch or awl, tap the screw hole locations. Holes must be vertically aligned.
3. Anchor Installation
Drill two 1/4” dia. Holes (A). If installing into a studs drill two 1/8” dia. holes and do not use Anchors (B). Insert Anchors (B) into Holes (A) and tap flush with the wall.
4. Wall Mount Installation
Place Wall Mount (A) into wall and inset Mounting Screws (B) through Wall Mount Holes (C) and tighten until Wall Mount (A) is flush with the wall. Do Not Over Tighten! Insert Front Cover (D) into Wall Mount (A)
5. Drop Elbow & Hose Installation
Apply PTFE plumbers tape on both ends of Pipe Nipple (A) (not included). Screw Pipe Nipple (A) into the elbow inside the wall. The Pipe Nipple (A) is to project 1/4” – 3/4” from the finished wall. Screw Drop Elbow (B) onto Pipe Nipple (A) and tighten until Drop Elbow (B) is property positioned and flush to the finished wall. Place Rubber Seal (C) inside Hex Hose Fitting (D). Connect Hex Hose Fitting (D) into Drop Elbow Outlet (E) by turning Hex Hose Fitting (D).
6. Unit Startup
Turn on hot and cold water supplies, and check all connections for leaks.
7. Final Flushing
For final flushing, turn the valve on and allow water to run through the Hose (A) for several minutes. Allow water to run for several minutes until all foreign matter clears the line.
8. Shower Arm Installation
Place Rubber Seal (A) inside Tapered Hose Fitting (B). Conned Hand Shower (C) to Hose (D) by turning Tapered Hose Fitting (B ) clockwise. Warning: Make sure Hand Shower (C) is securely tightened to Hose (D).
Body Jets Installation Instructions
|
Step 1:
|
|
|
Step 2:
|
|
|
Body sprays
|
|
|
|
Remove the decorative plate (A) out of the body.
|
|
|
Remove the screws from the outlet face (B) and connector body (C) with the Allen key (D).
|
|
Body Spray Installation Instructions
|
|
|
|
|
|
Step 3:
|
|
|
Step 4:
|
|
|
|
|
|
|
Screw the threaded pipe (E) to the water supply fittings. Push the plastic box (F) into the wall through the threaded pipe (E). Then, install the decorative plate (I) into the plastic box (F). Make sure the position is correct according to the diagram.
|
|
|
Screw the connector (G) into the threaded pipe (E) with the Allen key (H). Install the connector body (C) to the connector (G). When finish installation, please check to make sure the connection is completed. Then, fix the screws into the body (C) with Allen key (D) and make sure the body (C), connector (G) and decorative plate (I) are tightened. Make sure the one side with the bulge is in the top position.
|
|
|
Body Spray Installation Instructions
|
|
|
|
|
|
Step 5:
|
|
|
Step 6:
|
|
|
|
|
|
|
|
Install the outlet face (B) to the body (C). Make sure the connection of body (C) and outlet face (B) are completed. Tighten the screw through the outlet face (B) into the body (C) with the Allen key (D).
|
|
|
Install the decorative plate (A) into the outlet face (B) tightly. Make sure the hole and the raised dot are in the correct position when you push the decorative plate (A) into the outlet face (B).
|
|
|
Body Spray Installation Instructions
|
|
|
Mixer Installation
a. Release four handwheel levers according to the above directions.
b. Take apart the embed valve, panel, and handwheel.
1. Dig the embed space for the pipe on the wall according to the specification of the valve.
2. Dig 4 holes according to the position of the screws.
3. Use a hammer to thwack the screws into 4 holes.
4. Fix the valve body with 4 screws.
5. Find out the expansion screw heads with washer and spring washer. Use copper sleeve wrench to lock the screw heads with the embed valve body.
6. After connect all the pipes and before sealing the wall with concrete, confirm no leaking problem occur when turn on the water.
7. Fix the decorative panel on the embed valve body.
8. Screw the handwheel arms with the handwheels.
|
