How to install Fontana Reno Ceiling Mount Shower Head Set With 6 Body Massage Shower Jets | KRISTAL-SHOWER-HEAD-SET
Easy step by step Installation Instructions for Thermostatic Rainfall Shower System
Before you begin, please read the installation instructions below. Observe all local building and safety codes.
Unpack and inspect the product for any shipping damages. If you find damages, do not install.
Please note all products must be installed by a professional and certified plumber otherwise warranty might be voided.
shower
Ceiling Mount Shower Head Installation Instructions
Square Shaped Shower Head
Step 1:
Step 2:
Step 3:
Step 4:
Step 5:
Step 6:
Step 1: Take Out the Old Shower Head You can easily remove it by hand, but depending on how long the rain showerhead has been installed, you might need to use an adjustable wrench. Hence, if you find it difficult to remove, rotate the showerhead with an adjustable wrench in a counterclockwise direction to unscrew it.
Step 2: Keep the Shower Arm Clean and In Good Shape After you have removed the head, check the shower arm threads for any debris and old Teflon tape. If you find any, remove it and clean them off thoroughly. It’s best to use a microfiber cloth when cleaning the thread because it removes Teflon tape perfectly and works great to pick up tiny grits. Once you’re done cleaning, check if it is corroded or leaking. For damaged threads, it will be best you replace it entirely so you can have a comfortable shower experience any time.
Step 3: Time to Add New Teflon Tape Since you have removed the old Teflon tape, you have to replace it with new ones. The reason is that this tape helps to protect the shower from leaking after installing the showerhead. Now apply the new Teflon tape about 3-5 turns on the thread and tear the end part. Use your hands to smooth it out to keep it leveled to the thread. Keep in mind that when applying the tape, you should go in a clockwise motion so that it doesn’t come off when you attach the head in the same direction.
Step 4: Connect the Showerhead As said earlier in the tools needed, we’re using the rubber sealing washer that comes with the showerhead. This tool helps to make the showerhead stay watertight and secured on to the thread. Ensure you place it properly before installing it. After that, reconnect the shower head and tighten it down with your hands. You can employ a chair or ladder to make things easier for you.
Step 5: Tighten the Showerhead On To the Thread You will need to get the adjustable wrench handy to tighten down the shower very well. But make sure you wrap the threads with a terry cloth, so it doesn’t damage the finish when tightening the showerhead. Once you have done that, now use the adjustable wrench to tighten down the showerhead. However, don’t over-tight or force it so that it’s easier to remove in the future.
Hand Held Shower Installation Instructions
Size
Rts Included:
1. Wall Outlet 2. 60" Shower Hose With Gaskets 3. Complete Slide Bar With Mounting Parts / Posts, Screws & Anchors 4. Adjustable Shower Mount (Attached To Slide Bar) 5. Hand Held Shower
HandHeld Shower Installation Instructions
Handshower Installation Instructions
Supply Elbow Installation
Wall Bar Installation
Step 1:
Step 2:
Apply Plumber Tape To Threaded Ends Of 1/2" (13 Mm) Iron Pipe Nipple (Not Supplied) And Thread Into Shower Riser Elbow So That Nipple Extends Past The Finished Wall No More Than 0.2" (4.8 Mm) And No Less Than 1/16" (1.6 Mm). Place The Supplied Installation Gasket (1) Behind The Elbow (2). Screw The Supply Elbow Onto The Nipple Making Sure That The Supply Elbow Outlet Is In A Downward Facing Position. Minimum Diameter For Hole Is 1" (25 Mm) With A Maximum Of 1½” (38 Mm).
Caution: To Avoid Damage To The Supply Elbow Or Hose Finish During Installation, Wrap With A Cloth Or Tape And Use Only A Smooth-Jawed Wrench. DO NOT OVERTIGHTEN CONNECTIONS.
A. Select A Convenient Height To Place The Shower Rail Based On Your Personal Needs. Be Sure To Leave Enough Slack For The Hose Of The Hand Shower To Operate Freely When The Hand Shower Is Placed In The Extreme Up Or Down Positions. Note: If Possible It Is Recommended That The Slide Bar Brackets Be Secured Into The Wall Studs. For Ceramic Tile Installation, Drill Holes In Grout If Possible.
B. Mark The Place For Drilling The Hole For The Lower Post. Mark Using A Level, In A Vertical Line From The Lower Hole, The Placement Of The Upper Post Hole. Distance Approximately 25.7" (653 Mm).
Step 3:
Step 4:
Note: Hole Size Will Be Determined By Your Use Of Just The Screw Or Anchor And Screw For Installation. Drill Hole For Mounting Of Bottom Post. Start With A Smaller Drill Bit Size, 1/8" Is Recommended, And Drill Hole. If You Hit A Wall Stud, Go To Next Step. If You Do Not Hit A Wall Stud, Change To A Drill Bit Size Suitable For The Anchors, 1/4" Is Recommended, And Re-Drill Hole. Anchors Are For Use On Drywall Or Tile. For Fiberglass, Acrylic And Flat Plastic Surfaces, Use Toggle Bolts (Not Included). Before Drilling Top Mounting Hole, It Is Recommended That You Place The Assembled Slide Bar And Post Assembly (1) On Its Side Next To The Hole Locations You Have Marked. Make Sure Posts Are Pressed Fully Onto Bar. Align Centre Of Bottom Post With Bottom Hole That Was Just Drilled And Make Sure Centre Of Top Post Aligns With Mark For Top Hole. If Not, Re-Mark Top Hole Location. If It Aligns, Drill Top Hole In Location As Marked.
Insert Anchors (1) Into Drilled Holes. Slide Covers (2) Over Brackets (3), And Insert Screws (4) Into Bracket/Cover Assembly. Secure Assembly To Wall With Screws.
Slide The Slide Mechanism (1) And Elbow (2) Onto The Wall Bar (3). Slide Wall Bar Over Bracket Tabs (4) And Secure The Wall Bar Unit With Screws (5) Provided. Install Caps (6) Into Ends Of Wallbar. Lower Elbow (7) & Screw (8) Was Pre-Installed Prior To Shipping, Tighten Screw (9) If You Find It Is Sliding Inside Bar.
Step 5:
Step 6:
Connect The Shower Hose To The Wall Outlet (1) And The Hand Held Piece (2), Ensuring That The Internal Gaskets (3) Are Present In The Shower Hose Nuts. Normal 1/2" Rubber Gaskets Can Be Used.
Place The Conical Nut Of The Hose (4) That Is Connected To The Hand Held Piece, In The Slide Bar Holder (5) And Turn It To Desired Position.
To Slide The Mechanism Up Or Down, Push In On The Button (6) Of The Mechanism And Slide It On The Bar.
Step 7:
Care Should Be Given To The Cleaning Of This Product. Although Its Finish Is Extremely Durable, It Can Be Damaged By Harsh Abrasives Or Polish. To Clean, Simply Wipe Gently With A Damp Cloth And Blot Dry With A Soft Towel.
Maximum Flow Rate: 2.5 GPM
Shower Body Jets Installation Instructions
Step 1:
Step 2:
Body Sprays installation
Step 3:
Step 4:
Step 5: (Pressure Balancing Loop)
Rough-in Suggestion: This installation requires a 1/2" male threaded pipe fitting to extend 1/4" beyond the finished surface. The plumber should install a properly anchored 1/2" female pipe fitting (i.e. a drop-ear ell) recessed into the wall, into which a brass pipe nipple of proper length can be fitted once the finished wall is complete. Note: The hole size opening should be 1.5" max diameter. Bodyspray placement: Custom shower systems are sized to the user or users. Bodysprays are normally placed at the upper back, middle back, and upper thigh. Always position bodysprays according to the preferences of the user(s).
Pressure Balancing Loop: If installing bodysprays in a bank of 3 or fewer, a pressure balancing loop is not necessary. If installing bodysprays in a bank of 4 or greater, a pressure balancing loop must be used to keep the pressure even between the bodysprays.
Instructions Body jets should be arranged in your system to provide the necessary spray outlets to suit the application. 1. Identify all components and check for completeness, particularly before arranging fitting. 2. Depending on the application the body jet can be panel mounted using a backnut (not supplied) or set into the wall on rigid pipe work. If panel mounting care should be taken to ensure connection can be made after securing with the backnut. 3. Connect body jet to pipe work using recommended ½” BSP connections (not provided) with thread sealing compound where necessary. Note: - Before finishing wall turn on water supplies to check both correct system function and for leaking from joints/connections. 4. Complete wall finish.
Fontana Edinburgh Wall Mount Thermostatic Rainfall Shower Set With 6 Body Massage Jets
This beautifully designed square rainfall shower system will provide your bathroom with a touch of elegance and your muscles with the relief they need. This rainfall showerhead will provide relaxation while the six adjustable body massage jets will target the areas that need it most. Handheld shower and thermostatic faucet system included. Three lever control bathroom shower in brushed nickel or chrome finish is the perfect complement to today's modern home. This FontanaShower is ceiling mount complete shower head, handheld shower mixer set provides a luxurious showering experience and is the perfect complement to any modern bathroom. The modern design handheld shower, cold and hot water shower mixer and an easy-to-use mixer valve, made from high-quality. Be sure, when it comes to new bathroom rain shower sets, FontanaShowers is offering shape, finish, and styles you're looking for.
Features:
Brand Name: FontanaShowers
Model Number: CHROME-SQUARE-RAIN-SHOWER-HEAD
Water Outlets: Handheld Shower, Shower Head, Body-Jet Spray
.jpg)
