Home > Touchless Faucets Compatible with FontanaShowers
FontanaShowers touchless faucet installation in a commercial restroom (FS1096)
Contractor Center

Touchless Faucets Compatible with FontanaShowers

Spec, install, commission, and integrate Fontana touchless sensor faucets across commercial lavatories and stations. This hub includes BIM/Revit, CSI/specs, compatibility checks, and BMS telemetry guidance.

Overview

FontanaShowers® touchless faucets are designed for high-traffic commercial restrooms—airports, schools, healthcare, transit, and office campuses. Typical plumbing interfaces (1/2" supplies, standard hole patterns) make them broadly compatible with common sinks and handwashing stations. Always verify rough-ins, wall/deck thickness, and spout reach against your fixture schedule.

Hydraulics
Laminar 0.35–0.5 gpm recommended; regulate to site pressure; install Y-strainers (~200 μm) per fixture.
Safety
Anti-scald per ASSE 1070/ASME A112.1070/CSA B125.70; target ≤120°F (49°C) outlet.
Power
AC 100–240V with battery backup on many models; check each spec sheet for details.

Training Videos

Swap to your project videos anytime.

Sensor Faucet
Finish Options
Wall-Mounted

Recommended Fontana Touchless Models

Pick wall-mount or deck-mount to suit your lavatory/handwashing station. Match finish and flow to your spec and environment.

Wall-Mount (Matte Black)
FS1123 matte black wall-mount touchless faucet
Brio Wall-Mount — FS1123 Product Page · Specs (PDF) · Collection
Wall-Mount (Le Havre)
FS9824MB wall-mount touchless faucet
Le Havre — FS9824MB Product Page
Deck-Mount (Montpellier Series)
FS1096 deck-mount touchless faucet in matte black
FS1096 — Deck-Mount Matte Black · Chrome · Gold · Specs (PDF)
3-in-1 (Faucet + Soap + Dryer)
FS3004 integrated touchless faucet, soap dispenser, and hand dryer set
Integrated Set — FS3004 Product Page
Deck-Mount (Chrome)
FS7757CH chrome touchless faucet
TouchIQ™ — FS7757CH Product Page

Compatibility Notes

Mount & Thickness
For wall-mount valves/controllers, confirm wall cavity depth and service access. For deck-mount, verify deck thickness and hole Ø (often 1 3/8").
Reach
Match spout projection to bowl geometry to control splash at 0.35–0.5 gpm laminar.
Supply & Stops
Most models connect to 1/2" supplies. Include isolation valves per fixture and strainers.
Finish & Cleanability
PVD Matte Black, Chrome, Brushed Nickel/Gold options. Avoid high-gloss mirror surfaces directly opposite sensor windows.

Installation Essentials

Hydraulics
0.35–0.5 gpm laminar; regulate to site 60–80 psi; Y-strainer ~200 μm per fixture.
Mixing & Safety
ASSE 1070 / ASME A112.1070 / CSA B125.70; ≤120°F (49°C) outlet; label anti-scald.
Power
100–240 VAC primary; battery failover on many models; route low-voltage raceways where applicable.
Durability
Target IP65 electronics, vandal-resistant plates, locking M8/M12 connectors.

Commissioning Checklist

Response
Activation delay ≤ 200 ms; set max-on timeout per room type.
Sanitation
Program purge/flush cycles; validate thermal disinfection if used.
Integration
If connected, enroll devices to BMS; verify telemetry tags and alarms.
Training
Create QR-linked SOP for custodial/tech teams; place under service panel.
Water Savings ≥ 30% Fault Rate ≤ 0.25% / mo

Inspiration & Close-ups

Support

Include project name, fixture schedule, finish codes, power/controls notes, and required certifications in your submittal email.

Field Tips

Isolation
Use isolation valves per fixture; label shutoffs and circuit IDs.
Power
Hybrid AC/DC where feasible; keep spare battery packs for high-traffic banks.
Closeout
Record serials/firmware and attach commissioning logs to turnover set.