Fontana 20"x 40" Martinique Large Oil Rubbed Bronze Solid Brass LED Rain Showerhead System
Martinique's oversize rainfall showerhead provides all over coverage. This beautiful solid brass fixture with an oil rubbed bronze finish will look stunning in your bathroom. Six shower adjustable shower jets and a handheld shower for maximum coverage and relaxing massage for tired muscles. Built-in hydro-powered device powers the LED lights, which provide visual shower temperature cues to reduce water waste. The lights will dim and brighten when you lower and raise the pressure so you can set the perfect mood, water, and lighting. When water temperature is ≤89 °F (≤32 °C), Blue color will show automatically. When water temperature is between 97 to 107 °F (36-42 °C), Green color will show automatically. When water temperature is between 109 to 122 °F (43-50 °C), Red color will show automatically. When water temperature is above 122 °F (>50 °C), Red color will flash immediately.
Fontana 20"x 40" Martinique Large Oil Rubbed Bronze Solid Brass LED Rain Showerhead System Features:
Before you begin, please read the installation instructions below. Observe all local building and safety codes.
Unpack and inspect the product for any shipping damages. If you find damages, do not install.
Please note all showers must be installed by a professional and certified plumber otherwise warranty might be voided.
shower
Shower Head Installation Instructions
Shower Head Installation Instructions
Shower Parts
Shower Head Installation Instructions
Connect pipe 1 with decorative cover
Step 1:
shower
Step 2:
Draw the holes on the ceiling according to the Decorative Cover and pipes.
Drill the holes on the ceiling according to the hole specification and install 4 pipes.
Shower Head Installation Instructions
Step 3:
Step 4:
Put the screw bolts through the hole on the side to lock pipes.
Install the four-pipes on the showerhead.
Shower Head Installation Instructions
Step 5:
Step 6:
Shower Head Installation Instructions
1. Mark the fixing positions and drill holes to suit the anchors. 2. Install the anchors and fix the mounting bar to the ceiling with screws. 3. Screw the shower bars into the shower head tightly. 4. Attach the shower bar to the mounting bar and fix screws and nuts to lock shower bar with mountthe ing bar at the desired height. 5. Add screen washers. Screw shower hose (not included) to the water inlet on the showerhead and then to the water outlet in the ceiling.
Showerhead Installation Instructions
Hand-Held Shower Installation Instructions
Step 1:
Step 2:
Step 3 & 4:
Hand
Held
Shower
Hand Held Shower
Handheld Shower
Handheld Shower
Handheld Shower
Step 5:
Step 6 & 7:
Step 8:
1. Gather All Parts
2. Hole Locations For Wall Mount
Remove Front Cover (A) from Wall Mount (B). Use Wall Mount Screw Holes (C) to place the desired location. Using a punch or awl, tap the screw hole locations. Holes must be vertically aligned.
3. Anchor Installation
Drill two 1/4” dia. Holes (A). If installing into a studs drill two 1/8” dia. holes and do not use Anchors (B). Insert Anchors (B) into Holes (A) and tap flush with the wall.
4. Wall Mount Installation
Place Wall Mount (A) into wall and inset Mounting Screws (B) through Wall Mount Holes (C) and tighten until Wall Mount (A) is flush with the wall. Do Not Over Tighten! Insert Front Cover (D) into Wall Mount (A)
5. Drop Elbow & Hose Installation
Apply PTFE plumbers tape on both ends of Pipe Nipple (A) (not included). Screw Pipe Nipple (A) into the elbow inside the wall. The Pipe Nipple (A) is to project 1/4” – 3/4” from the finished wall. Screw Drop Elbow (B) onto Pipe Nipple (A) and tighten until Drop Elbow (B) is property positioned and flush to the finished wall. Place Rubber Seal (C) inside Hex Hose Fitting (D). Connect Hex Hose Fitting (D) into Drop Elbow Outlet (E) by turning Hex Hose Fitting (D).
6. Unit Startup
Turn on hot and cold water supplies, and check all connections for leaks.
7. Final Flushing
For final flushing, turn the valve on and allow water to run through the Hose (A) for several minutes. Allow water to run for several minutes until all foreign matter clears the line.
8. Shower Arm Installation
Place Rubber Seal (A) inside Tapered Hose Fitting (B). Conned Hand Shower (C) to Hose (D) by turning Tapered Hose Fitting (B ) clockwise. Warning: Make sure Hand Shower (C) is securely tightened to Hose (D).
HandHeld Shower Installation Instructions
Shower Body Jets Installation Instructions
Step 1:
Step 2:
Body sprays
Remove the decorative plate (A) out of the body.
Remove the screws from the outlet face (B) and connector body (C) with the Allen key (D).
Body Spray Installation Instructions
Step 3:
Step 4:
Screw the threaded pipe (E) to the water supply fittings. Push the plastic box (F) into the wall through the threaded pipe (E). Then, install the decorative plate (I) into the plastic box (F). Make sure the position is correct according to the diagram.
Screw the connector (G) into the threaded pipe (E) with the Allen key (H). Install the connector body (C) to the connector (G). When finish installation, please check to make sure the connection is completed. Then, fix the screws into the body (C) with Allen key (D) and make sure the body (C), connector (G) and decorative plate (I) are tightened. Make sure the one side with the bulge is in the top position.
Body Spray Installation Instructions
Step 5:
Step 6:
Install the outlet face (B) to the body (C). Make sure the connection of body (C) and outlet face (B) are completed. Tighten the screw through the outlet face (B) into the body (C) with the Allen key (D).
Install the decorative plate (A) into the outlet face (B) tightly. Make sure the hole and the raised dot are in the correct position when you push the decorative plate (A) into the outlet face (B).
Attach the positioning bar to the rough-in body (4,5) with tapping screws. Mark the location of the mounting holes.
Remove the rough-in body and drill pilot holes at the locations marked in the previous step. Insert anchors.
Shower Valve Mixer Installation Instructions
Step 5:
Step 6:
Attach the rough-in body to the wall.
Connect the rough-in body to the water supply pipes according to the diagram.
Shower Valve Mixer Installation Instructions
Step 7:
Step 8:
Finish the wall surrounding the shower with a thickness of 1/2"-1-1/2".
a) Finished wall surface should not exceed the upper edge of the installation box.
If the tile exceeds the edges of the installation box, trim the tile as necessary to install the trim plate.
b) Trim the tile around the installation box as necessary.
Shower Valve Mixer Installation Instructions
Step 9:
Remove the plastic guard and place the trim plate over the installation box. Install the screws covers, handles and buttons.
Shower Valve Mixer Installation
How to install the Shower Set with Wall Mount Showerhead, Hand Held Shower and Shower Mixer