Fontana Diadema 20" * 40" Large Oil Rubbed Bronze Solid Brass LED Rain Shower Head with Body Jets & Handheld Shower
Diadema is a complete shower system that offers all you can dream about for the perfect shower experience. The extra large rainfall shower head is 20”x40” has oil rubbed bronze finish and it comes with matching shower arm. It also incorporates LED lightning that do not require any external source of electrical supply, it is powered and activated by the water flow. The color changes according to the water temperature, so you will never be tacked by surprise and the intensity varies according to that of the water flow. 6 adjustable body jets are included, so you can fully enjoy the benefits of a refreshing water massage. Installation is easy, as everything comes with standard threading. Only the best materials have been used – solid brass and stainless steel, for a long lasting life time. It comes complete with accessories and installation instructions.
Fontana Diadema 20" * 40" Large Oil Rubbed Bronze Solid Brass LED Rain Shower Head with Body Jets & Handheld Shower Features:
1.Drawing the line on the ceiling according to the above specification ·Decorative Cover ·pipe 1
2.connect pipe 1 with decorative cover
3.Drill the holes on the ceiling according to the above hole specification and install 4 pipes.
4. According to the right drawing, install four-pipe 2 into pipe 1. Put the screw bolts through the hole on the side to lock pipe 2 with pipe 1.
5.As the right drawing is shown, install four-pipe 2 on the head shower.
6.After fixing the showerhead on the ceiling, connect the showerhose with 2 water inlet on the showerhead back cover. The other end connects with the water outlet pipe in the wall.
Remarks: Ceiling mounted shower head come with fixing bar installation
1. Draw size on ceiling
2. Install fixing bar on ceiling
3. Install fixing bar on shower head
4. Put shower head bar on ceiling fixing bar.
The showerhead installation is now complete.
Body-Jet Installation Install the Supply Piping
Multiple Bodyspray Installation
•Water Supply
•Nipple Mamelon Nipple
•Pressure Balancing Loop
1. Route the water supply lines.
2. If installing more than one bodyspray off the same supply line, construct a pressure balancing loop. Locate a tee along the loop at each bodyspray installation location.
3. Do not strap the pipes at this time.
Single Bodyspray Installation
•Nipple Mamelon Nipple
1. Route the water supply line.
2. Install an elbow to the end of the supply pipe at the bodyspray installation location.
Install the Plaster Guard
Install the Plaster Guard
•Elbow (or Tee)
•Install the plaster guard
Set Piping Depth
Align mark with front of the stud face
•Thin Wall
Align mark with front of the stud face
•Standard Wall
Install the plaster guard. Push until the plaster guard is snug against the face of the elbow (or tee).
1. Install the water-resistant wall board.
2. Cut out a 4" (10.2 cm) to 4-1/4" (10.8 cm) square at each the installation location.
3. Install the finished wall material
•Escutcheon
•Leak Shield
•Adapter
•Extension
•Socket Wrench With Bit
•Screw
•Waterway Passage
1. Insert the escutcheon into the rough opening. The double ribs of the leak shield should be facing up.
2. If the leak shield makes contact with the elbow: Enlarge the hole in the back of the leak shield to 1-1/4" (3.2 cm).
3. Thread the adapter onto the nipple using the provided 11 mm bit, 11 mm or 7/16" socket, extension and socket wrench. Use masking tape to hold the bit in place, as the bit could fall off and cause damage.
IMPORTANT! The escutcheon should sit loosely at this point. If it is tight against the wall, use a longer pipe nipple.
4. Align the groove in the waterway with the double ribs on the leak shield.
5. Press the waterway into place over the adapter. Secure the waterway to the adapter with the screw provided.
6. Verify that the escutcheon does not turn or shift.
With the ribs of the sprayhead facing up, install the sprayhead to the waterway.
Hand-Held Shower Instructions
5. HOLE LOCATIONS FOR WALL MOUNT
Remove Front Cover (5A) from Wall Mount (5B). Use Wall Mount Screw Holes (5C) to place the desired location. Using a punch or awl, tap the screw hole locations. Holes must be vertically aligned.
ANCHOR INSTALLATION
Drill two 1/4” dia. Holes (6A). If installing into a studs drill two 1/8” dia. holes and do not use Anchors (6B). Insert Anchors (6B) into Holes (6A) and tap flush with wall.
WALL MOUNT INSTALLATION
Place Wall Mount (7A) into wall and inset Mounting Screws (7B) through Wall Mount Holes (7C) and tighten until Wall Mount (7A) is flush with the wall. Do Not Over Tighten! Insert Front Cover (7D) into Wall Mount (7A)
DROP ELBOW & HOSE INSTALLATION
Apply PTFE plumbers tape on both ends of Pipe Nipple (8A) (not included). Screw Pipe Nipple (8A) into the elbow inside the wall. The Pipe Nipple (8A) is to project 1/4” – 3/4” from the finished wall. Screw Drop Elbow (8B) onto Pipe Nipple (8A) and tighten until Drop Elbow (8B) is property positioned and flush to the finished wall.
Place Rubber Seal (8C) inside Hex Hose Fitting (8D). Connect Hex Hose Fitting (8D) into Drop Elbow Outlet (8E) by turning Hex Hose Fitting (8D).
UNIT STARTUP
Turn on hot and cold water supplies, and check all connections for leaks.
FINAL FLUSHING
For final flushing, turn the valve on and allow water to run through the Hose (10A) for several minutes. Allow water to run for several minutes until all foreign matter clears the line.
11. SHOWER ARM INSTALLATION Place Rubber Seal (11A) inside Tapered Hose Fitting (11B). Conned Hand Shower (11C) to Hose (11D) by turning Tapered Hose Fitting (118) clockwise.
