Home > How to Install Fontana Mugla 22" Brushed Nickel LED Thermostatic Waterfall Shower?

How to install Fontana Mugla 22" Brushed Nickel LED Thermostatic Waterfall Rain Shower Head With Massage Body Sprays And Hand Shower | FS-5925N

Visit Product Page
Installation Instructions for Bathroom Shower Set
  • Before you begin, please read the installation instructions below. Observe all local building and safety codes.
  • Unpack and inspect the product for any shipping damages. If you find damages, do not install.
  • Please note all products must be installed by a professional and certified plumber otherwise warranty might be voided.
 shower Fontana Mugla 22" Brushed Nickel LED Thermostatic Waterfall Rain Shower Head With Massage Body Sprays And Hand Shower

Shower Head Installation Instructions

Size:

Open the top cover and drill according to the marked position.
1. Mark by the position of the four holes.
2. Take care to avoid wires and pipes to prevent damage.
3. Be sure to confirm that the four holes are on the same horizontal line. 		Remove the protective cover (F). Mark the positions and drill holes to suit the anchors (A). Install the anchors (A) and fix the rough-in valve (B) into the wall with screws. Use a level to ensure that the rough-in valve (B) is straight and level. (Important: Flush the water supply to remove any dirt and debris before installing the valve body).

Wrap Teflon tape around the pipe threads and connect water supply lines and in-wall pipes (not included) as desired to the rough-in valve (B). Turn on the water supply and open the cartridge to check for leakage. Then put on the protective cover and finish the wall surrounding the valve. (Note: Test the water pressure after the pipe connections have been made and before the finished wall material is installed).

Two inlet fittings are connected to the pipe joint of the wall; then the nut, expansion screw, and inlet pipe are connected.

Reinstall the top cover.
Fix the escutcheon (D) to the showerhead (E) with screws (C).


Remove the protective cover when the finished wall is completed. Then, install the showerhead (E) and press it against the finished wall



HAND-HELD SHOWER INSTALLATION INSTRUCTIONS



Step 1: Step 2:
Hand
Held
Shower 		Hand
Held
Shower
Handheld Shower
Step 3: Size:

Handheld Shower
Holder Size

Hand Shower Outlet Installation

• Complete the outlet pipework ensuring it ends in an appropriate 15mm x 1/2" BSP female thread elbow.
Note: This fitting is not supplied as variations in installations require the selection of a suitable solder or compression fitting.

• Install the 'Wall Outlet', thread long male 1/2" BSP into the appropriate female fitting using PTFE tape to give a watertight joint.
Note: The thread can be cut to size if required. Make sure that all debris is removed from the connector and the section that has
been cut is dressed correctly, before installation.

The minimum required water pressure is 0.05 MPa (0.5 bar).
Flow rate 2.5 GPM (9.5 L





Shower Body Jets Installation Instructions

Step 1:
Step 2:
Body Sprays
installation
Step 3: Step 4:

Step 5: (Pressure Balancing Loop)




Rough-in Suggestion:
This installation requires a 1/2" male threaded pipe fitting to extend 1/4" beyond the finished surface. The plumber should install a properly anchored 1/2" female pipe fitting (i.e. a drop-ear ell) recessed into the wall, into which a brass pipe nipple of proper length can be fitted once the finished wall is complete.
Note: The hole size opening should be 1.5" max diameter.

Bodyspray placement:
Custom shower systems are sized to the user or users. Bodysprays are normally placed at the upper back, middle back, and upper thigh. Always position bodysprays according to the preferences of the user(s).

Pressure Balancing Loop:
If installing bodysprays in a bank of 3 or fewer, a pressure balancing loop is not necessary.
If installing bodysprays in a bank of 4 or greater, a pressure balancing loop must be used to keep the pressure even between the bodysprays.

Instructions
Body jets should be arranged in your system to provide the necessary spray outlets to suit the application.
1. Identify all components and check for completeness, particularly before arranging fitting.
2. Depending on the application the body jet can be panel mounted using a backnut (not supplied) or set into the wall on rigid pipe work. If panel mounting care should be taken to ensure connection can be made after securing with the backnut.
3. Connect body jet to pipe work using recommended ½” BSP connections (not provided) with thread sealing compound where necessary.
Note: - Before finishing wall turn on water supplies to check both correct system function and for leaking from joints/connections.
4. Complete wall finish.



THERMOSTATIC MIXER INSTALLATION INSTRUCTIONS Connection






Fontana Mugla 22" Brushed Nickel LED Thermostatic Waterfall Rain Shower Head With Massage Body Sprays And Hand Shower

Beautifully constructed of solid brass with brushed nickel finish. This generously sized waterfall/rainfall shower head that will provide relaxation beyond your imagination. The additional massage jets and handheld shower will help target your muscles and maximize your bathing experience. Built-in hydro-powered device powers the LED lights, which provide visual shower temperature cues to reduce water waste. The lights will dim and brighten when you lower and raise the pressure so you can set the perfect mood, water, and lighting. When the water temperature is ≤89 °F (≤32 °C), the Blue color will show automatically; When the water temperature is between 97 to 107 °F (36-42 °C), the Green color will show automatically; When the water temperature is between 109 to 122 °F (43-50 °C), Red color will show automatically; When the water temperature is above 122 °F (>50 °C), Red color will flash; When water temperature is above 122 °F (>50 °C), Red color will flash immediately

Features:

  • Brand Name: FontanaShowers
  • Model Number: FS-5925N
  • Finish: Brushed Nickel
  • Installation Type: Wall Mount
  • Material: Solid Brass
  • Feature: Thermostatic Shower, LED Shower Head
  • Shower Head Size: 21.6"x 9" (55cm x 23cm)
  • Body-Jet Size: 1.9" diameter (5cm)
  • Thermostatic Control Valve: Three handle control four-way
  • Connection: US G1/2" connection
  • Nut: 1/2" connection for the hose
  • Mixer control valve: Included
  • Qty 6 - 2"x 2" Body Jets
  • All installation parts included
    		•  Fontana Mugla 22" Brushed Nickel LED Thermostatic Waterfall Rain Shower Head With Massage Body Sprays And Hand Shower
    Fontana Mugla LED Shower Installation
    Install the Mugla 22-Inch LED Waterfall Shower
    Coordinate the large shower head, thermostatic controls, waterfall and rainfall functions, body sprays and hand shower.
    Installation Hub
    All Installation Guides Shower Installation Hub
    Shower Head
    Rain and Waterfall Requirements
    Thermostatic Valve
    Thermostatic Mixer Guide
    Body Sprays
    Body Jet Installation
    Hand Shower
    Handheld Installation
    Valve Rough-In
    Valve Rough-In Detail
    VIEW SHOWER INSTALLATION GUIDES →

    Frequently Asked Questions

    What should be verified before installing the Mugla shower?

    Confirm shower-head support, valve capacity, outlet routing, available flow and the exact LED-system requirements. Review Shower Requirements

    Can all Mugla shower outlets run simultaneously?

    Confirm approved simultaneous use from the product documentation and available pressure and flow before rough-in.

    When should concealed piping be tested?

    Flush and pressure-test the shower-head, body-spray and hand-shower piping before enclosure.

    What should commissioning include?

    Verify temperature control, outlet selection, spray balance, waterfall and rainfall delivery, LED operation and leaks.

    Fontana Mugla 22-inch LED thermostatic waterfall rain shower installation


    BathSelect Ancient Round Antique Rainfall Wall ShoweBathSelect Ancient Round Antique Rainfall Wall Shower Head Installation Instructions Head Installation Instructions